Which is better in the work of the analysis (FEA)? Solid works or ANSYS?

More Nabeel Allawy's questions See All

Can we apply NNs, Fuzzy Logic, and/or classical PR methods to calculate/predict the carbon footprint of an organizations towards the Net-Zero target?

Accelerating the path to Net-Zero emissions has become a paramount strategy for governments and organizations. I am interested in discussing the applications of the methods mentioned in the...

16 December 2023 4,556 3 View

Was bedeuted genau ein Protokolschreibung in Deutsche unis?

Kollegen, Studenten und Studentinnen, Ich studiere seit einigen Monaten meinen Master an der Uni Greifswald in Deutschland und leide sehr unter dem Problem des Protokollschreibens und finde es...

22 April 2023 2,531 1 View

Effect of INF y on Cancer cells A 549?

My superviser at the university asked me to give him a comparism of 4 groups (am group1 ) and I obtained the following table! Please help me because I was comparing my results with other 3...

22 April 2023 3,527 0 View

Can one use MiniSeq Ilumina NGS for Human cell sequancing ?

the Miniseq cost 20,000 $, is it possible to use it for Diagnostic purposes ? and is it possible to use it for human DNA sequancing? Is it siutable and practical for this purpose ? Is there is...

15 April 2023 7,940 0 View

Whats the difference between translectome and transelation ?

translatome refers to the entirety of mRNAs associated with ribosomes for protein synthesis Dose that mean it will take only one specific mRNA that is expressed under spesific condition in...

12 April 2023 5,977 1 View

What is differential gene expression?

i did not find any resonable defination for the DGE can anyone define this tearm for me please ?

12 April 2023 9,770 3 View

A question in NGS , what dose the following sentence mean ?

"during both the sample preparation and computational analysis phases, at which imperfections and biases may be introduced. These limitations may affect the ability of the experiment to address...

12 April 2023 6,366 2 View

Whats the differences between Microtaxonomics and Metagenomics?

which method should be more succeful and realabel in idetifing Microbiota Metataxonomics or the shutgun ?

10 April 2023 9,535 4 View

I have to prepare a report of Flourescence Immunoassay ?

Hallo everyone, am Having diffeculties in preparing my report of immuno flourescent assay as I have no previous knowlage about it. can anyone please help me in reading these picture of spleen...

30 March 2023 6,772 0 View

Mass Spectrophotometry peaks?

Please Sceintists am new Master Students and am finding alot of diffeculties in understanding the Mass Spectrophotometry Can anyone help me in explaining these Peaks? why it reads number 80 or...

21 March 2023 1,435 4 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View

Debrayan Bravo Hidalgo

In my opinion, ANSYS is a very good option.

Bhagyashree Chandrakant Prabhune

ANSYS would be a better option. You may get better interface, tools to solve the problem.

Eswara Prasath Murugan

In my perception, Ansys workbench would be better than solidworks. Because the templates for supplying the parameters is easily found in Ansys workbench than Solidworks.

Francisco Meira

ANSYS is a more detailed software but for beginners, if your analysis is a simple one, SW is more friendly. You may know you can import models from SW (and other software) to ANSYS in case you want to compare the capabilities between these great FEA systems.

Muhammad Ali

I suggest ANSYS https://www.ansys.com/ .