I would like to know which brand and what type of activated charcoal or activated carbon (lab grade) that I should use to purify plasma samples from impurities or endogenous compound for HPLC use.
ThankYou
I would like to ask, which type of syringe filter is suitable to purify extracted plasma samples for HPLC Analysis. Currently, my extraction method involves mixing mice plasma with saline,...
04 May 2018 935 6 View
I dont quite understand the following and would like to clarify the meaning: 1. For Lower Limit of Quantification (LLOQ), the analyte response at the LLOQ should be at least 5 times the response...
07 August 2017 6,856 5 View
I am going to do a biodistribution studies on tocotrienol in vivo. Previously my tocotrienol was tagged with a fluorescent probe. However, I would like to change my approach and using a...
03 April 2017 4,249 0 View
I am currently doing a fluorescence intensity scan with my compound. I am using the following parameters: Excitation: 273-276nm Slit: 20 Smoothing: 40 As my concentration increases from 20ug/ml...
10 November 2016 7,791 3 View
10 November 2016 3,607 0 View
I would like to know if there is any publication that supports the use of clean mouse plasma (eg. from sigma) to use it as a support for the calibration curve when compared to the PK of a mice...
09 October 2016 8,826 0 View
05 June 2016 5,439 8 View
05 June 2016 2,520 0 View
A powder extract is dissolved in pure DMSO first and diluted with sterile saline (0.9% NaCl) at 50 mg/ml with the final DMSO concentration at 10% Does this mean that the poweder of 50mg is...
06 July 2015 4,487 0 View
If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis
02 March 2021 7,670 3 View
So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...
02 March 2021 1,146 2 View
Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...
01 March 2021 1,907 3 View
I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...
01 March 2021 5,475 2 View
Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...
26 February 2021 10,014 3 View
Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...
25 February 2021 3,292 3 View
Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....
24 February 2021 5,383 5 View
I am currently trying to stain for PI3KBeta in MDA-MB-231 cells. My current issue is that 1) beta stains all over the cell and 2) there is an increase in signal at the edge of the cell and this...
24 February 2021 8,582 1 View
To do liquid biopsy and look for specific gene expressions there are so many published papers. Thera are different protocols and procedures used to isolate circulating cell free RNA or mRNA from...
23 February 2021 7,326 5 View
I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...
23 February 2021 3,262 5 View