What will be the die specification to cut Anode, Cathode and Separator for CR2032 coin cell (LIBs) ?

Hi Everyone Since I have CR2032 coin cell for lithium ion battery, what will be the die specification in mm for Anode, Cathode and Separator ? I am bit confused. Everywhere looks different...

10 November 2019 2,296 3 View

How will be the TG/DTA helpful to evaluate the carbon content in the sample?

05 June 2019 6,316 2 View

The theoretical capacity of NiMnO3 (Anode Material) is 994.9 mAh/g. is it correct?

I wanted to calculate the theoretical capacity of NiMnO3, which will be use as anode material for LIB. It is very hard to get it through literature. So I have calculated it like this: NiMnO3 +...

03 April 2018 4,205 4 View

Any literature availability where interparticle pores and intrapores of porous nanomaterials are discussed ?

Kindly help me to find out the detail discussion about interparticle pores and intrapores present in a porous nanomaterials.

31 December 2017 9,582 0 View

If sample is mesoporous and EIS spectra (Nyquist plot) shows deformed semicircles, how it is connected with porous path ways extrinsically ?

If sample is mesoporous and EIS spectra (Nyquist plot) shows deformed semicircles, how it can be correlated with Li+ conducting extrinsically over different porous path ways, in addition to...

31 December 2017 3,433 1 View

Is it correct that mesoporous structures gives large XRD peaks in small 2 theta ranges due to the regular arrangements of porous channels and cages ?

is it correct that mesoporous structures gives large XRD peaks in small 2 theta ranges due to the regular arrangements of porous channels and cages ? If the sample is mesoporous, but XRD peaks...

31 December 2017 8,907 5 View

Water based Battery?

We have made a 2.0 V battery with Graphite and Aluminium electrodes. When we spray water, we started getting stabilized current and LED glow. What will be the oxidation/reduction reaction on both...

03 April 2017 6,284 5 View

Impact factor link ?

Any one has link to get new impact factor of the journals. Thanks

03 April 2017 7,810 0 View

Can someone help me with half cell battery fabrication?

06 July 2015 2,084 14 View

How can a sodium ion system use the electrolyte at lower decomposition potential?

If a rechargeable sodium-ion battery with good performance characteristics could be developed, it could have the advantage of using electrolyte systems of lower decomposition potential due to the...

09 October 2014 7,054 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View