What will be the die specification to cut Anode, Cathode and Separator for CR2032 coin cell (LIBs) ?

Hi Everyone Since I have CR2032 coin cell for lithium ion battery, what will be the die specification in mm for Anode, Cathode and Separator ? I am bit confused. Everywhere looks different...

10 November 2019 2,296 3 View

What thickness of copper foil we should use for lithium ion battery electrode?

Dear Friends What should be the standard thickness of copper foil to use as anode electrode fabrication for lithium ion battery. There are 3-4 option available such as 8, 10, 12, 15...

06 July 2018 3,450 0 View

The theoretical capacity of NiMnO3 (Anode Material) is 994.9 mAh/g. is it correct?

I wanted to calculate the theoretical capacity of NiMnO3, which will be use as anode material for LIB. It is very hard to get it through literature. So I have calculated it like this: NiMnO3 +...

03 April 2018 4,205 4 View

Any literature availability where interparticle pores and intrapores of porous nanomaterials are discussed ?

Kindly help me to find out the detail discussion about interparticle pores and intrapores present in a porous nanomaterials.

31 December 2017 9,582 0 View

If sample is mesoporous and EIS spectra (Nyquist plot) shows deformed semicircles, how it is connected with porous path ways extrinsically ?

If sample is mesoporous and EIS spectra (Nyquist plot) shows deformed semicircles, how it can be correlated with Li+ conducting extrinsically over different porous path ways, in addition to...

31 December 2017 3,433 1 View

Is it correct that mesoporous structures gives large XRD peaks in small 2 theta ranges due to the regular arrangements of porous channels and cages ?

is it correct that mesoporous structures gives large XRD peaks in small 2 theta ranges due to the regular arrangements of porous channels and cages ? If the sample is mesoporous, but XRD peaks...

31 December 2017 8,907 5 View

Water based Battery?

We have made a 2.0 V battery with Graphite and Aluminium electrodes. When we spray water, we started getting stabilized current and LED glow. What will be the oxidation/reduction reaction on both...

03 April 2017 6,284 5 View

Impact factor link ?

Any one has link to get new impact factor of the journals. Thanks

03 April 2017 7,810 0 View

Can someone help me with half cell battery fabrication?

06 July 2015 2,084 14 View

How can a sodium ion system use the electrolyte at lower decomposition potential?

If a rechargeable sodium-ion battery with good performance characteristics could be developed, it could have the advantage of using electrolyte systems of lower decomposition potential due to the...

09 October 2014 7,054 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

Where can I find atmospheric measurement profiles (temperature, density, etc.) between 300-800 km altitude?

I am investigating thermospheric mass density profiles between 300-800 km altitude. I would like to compare the variability with other parameters, including temperature, electron content,...

01 March 2021 5,902 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

Does anyone know of a predictable relationship beween surface gravity and atmospheric composition?

The attached file demonstrates that there is a predictable relationship between the structural density of a terrestrial body and its none-rotating surface gravity. Using Newton's gravity law of...

26 February 2021 2,317 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View