What is the maximum number of reads per one run with NGS?

More Marko Radojković's questions See All

OEP BTS Engineering - 32 marker model?

Hello, Do any of you have experience with the analysis of chest wall compartments using a 32-marker model? Currently, we are using the standard 89-marker model, which is very time-consuming. Is...

26 October 2023 9,124 1 View

Why do I get endothermic ITC peaks upon titration of substrate to buffer blank?

Hello. This year we started using ITC in a bit unconventional way to study enzyme kinetics of beta-lactamase (there is already literature data that showed it works). The principle is fairly...

06 September 2023 1,801 3 View

Reference style for JSCR in Endnote online?

Hello! I'm using Endnote online and need help finding a reference style similar to JSCR, as the JSCR official reference style is not in Endnote online. Can anyone help? Thank you!

24 July 2023 6,200 1 View

Viruses that infect plasmodium?

Each life form has its own viruses. I am wondering if Plasmodium has specific viruses as well and which could be utilized as a measure to reduce Malaria infections? A virus which infects a...

16 January 2023 4,922 2 View

Why are phages specifc to bacteria and not other species?

Of course, phages do only interact with bacteria which have specific binding proteins. But why do only bacteria have these binding proteins? What if vertebrate cells would have these binding...

07 January 2023 1,583 4 View

How to add PBS ions in CHARMM-GUI for an AMBER ff simulation?

Here is what I'm trying to do: to solvate a peptide in water and ions that would mimic a PBS solution. To do this I tried uploading my peptide into the Solution Builder, adding the following...

13 December 2022 4,331 0 View

Where to buy ultrasonic probe for 2-5 MHz range for photoacoustic measurement?

Dear RG community, I'm starting a photoacoustic project, and I need to acquire some ultrasonic receivers. Acoustics is not my expertise, so I'm asking here for help! :D Where to buy, what is...

28 September 2022 4,408 6 View

ANSYS simulation, more specific about transient structural simulations?

Hi there, I am a student who is very new to ANSYS. I want to simulate the following scenario A flexible rod is connected to a rigid hub. The hub starts from 0 rad/s at 0ͦangle and reaches 100...

25 September 2022 1,560 0 View

Could anyone identify this or these, I suppose, mosses?

The photos are from the inland of Sao Miguel - Azores.

22 September 2022 1,972 5 View

Weekly insulin levels in wild mice?

With ongoing development of real-time "Free Style Libre" insulin detectors, has anyone ever did insulin analysis over a week period for a wild "forest" mice (not wild type lab mice)?

15 August 2022 7,487 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

How to confirm the site-directed mutagenesis result without performing NGS?

I'm cloning a fragment of 3200 nts into plasmid. The cloning was successful, however, 02 amino acids were mutated. Now I want to fix these 02 aa by site-directed mutagenesis technique using...

08 August 2024 4,645 2 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

Where should the ARS sequence be introduced on a plasmid?

Hi all, I need to introduce an ARS (autonomously replicating sequence) in my plasmid but I'm not sure which position would be the best. Does anyone have any suggestion? A picture of the plasmid...

05 August 2024 1,573 4 View

Why after performing site directed mutagenesis ,I don't see any colony after transformation?

I want to introduce a point mutation (change in one nucleotide) into my gene of interest (DNA binding domain) I have designed primers as recommended on the Data sheet of the kit : -Both primers...

05 August 2024 9,059 3 View

Why my colony PCR results of my recombinant bacterial not showing any results?

I am performing ligation of the plasmid and a target gene. The steps I have taken are: 1. Double digestion of the plasmid and target gene 2. Ligation of the plasmid with the target gene 3....

05 August 2024 2,570 3 View

People weight in Oaxaca Blinder Decomposition on R?

Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...

04 August 2024 6,033 0 View

Does anyone have issues using Prepman Ultra reagent for MicroSeq ID bacterial, fungal and yeast sample preparation?

I have been attempting to extract DNA from Bacterial, Fungal and Yeast banked samples (>1e7 cells) using Prepman Ultra reagent and I seem to be struggling to obtain a sequence. Although the...

01 August 2024 2,079 0 View

Transfection in HEK293T cells?

Dear All, I am trying to transfect a pCDNA3.1 vector containing my gene of interest. The purpose is to figure out the localization of the protein of interest. I have fused the protein with GFP on...

31 July 2024 9,892 4 View

Where to find a gene list for CRISPRa/i library screening of regulatory factors that affect pathogenic Th17 differentiation in PBMC?

I want to perform a CRISPRa/i library screening for candidate regulatory factors that affect pathogenic Th17 differentiation in PBMC. But I am wondering how to define the size of gene library, so...

31 July 2024 2,150 0 View

Marko Radojković

SAMEE ULLAH

Thank you for the link. Still, I am not quite sure what does output folder size mean. If the size is 22-26 GB, does it mean you get 22-26 x 10^9 sequences as result?

Annemarie Honegger

A better link is this page on the same site:

https://emea.illumina.com/systems/sequencing-platforms.html?langsel=/ae/

Scroll to the bottom of the table for the maximal number of reads per run, which depends on the specific platform and is cited to be between 4 million for the isSeq100 and 1 billion for the NextSeq 2000