What is the connection between deposition rate and accretion pattern ?

Kaviarasu Chinnaiyan @Kaviarasu-Chinnaiyan

17 September 2018 0 8K Report

Can any one help me in understanding the connection between deposition rate and accretion pattern while using DPM Model in ANSYS Fluent?

Badges
Science topic

More Kaviarasu Chinnaiyan's questions See All

DNA isolation methods - DNA yield is lesser in micro wave method then in salting out method and commercial kit method. Why?

We are isolating DNA from wax embedded Squamous cell carcinoma (SCC) tissues. We take tissue sections and isolate the DNA from that. We following 3 methods for a comparison study. Those methods...

24 November 2017 8,482 0 View

How to induce nephrotoxicity in Wistar rats?

I wish to induce nephrotoxicity in Wistar rats by using nicotine. I would like to know how much concentration of nicotine to be used for the induction to animal. It would be thankful If u could...

09 November 2017 4,397 0 View

During DNA isolation how do u make sure that you have isolated only the DNA not RNA?

While isolating DNA how do we make sure that we have isolated only the DNA at the end not RNA? At which step the DNA alone get separated and which buffer and composition is used for that... Thank You

24 October 2017 7,255 4 View

In LES method, how to incorporate the surface roughness for pipe?

In flow analysis for rough pipe using Large Eddy Simulation, how the roughness height and roughness constant value can be incorporated. Is it possible?....

26 February 2017 5,486 5 View

What is the thermophysical properties of copper oxide nanoparticle ?

Looking for the thermophysical properties of copper oxide for size greater than 50 nm in diameter.

28 January 2017 6,237 2 View

How to do DPM (Nanoparticle dispersed in air) for a 90 degree bend using LES?

Using Nanoparticle as discrete phase and air as continuous phase, how to do modelling for calculating the flow and deposition rate on walls of pipe having 90 degree bend. Kindly share some...

19 January 2017 9,726 2 View

Can any one tell me the important genes involved in adipogenesis regulation during type-2 diabetic condition?

I would like to know the important genes involved in adipogenesis regulatory mechanism during high fat fed condition in Wistar rats or during type-2 diabetic condition...

20 May 2014 8,617 4 View

How to calculate the gain value Kp and Ki for the current controller of Matrix converter?

I have attached the block diagram of the control. I'm trying to implement the SPWM switching sequence and control the matrix converter(Three phase to single phase). The output of the Matrix...

01 January 1970 7,562 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View