spray jet,nozzle
How Reacting Multiphase flow model available with OPENFOAM is different from eulerian model of ANSYS Fluent? What are the governing equations and where can we find the closure schemes of various...
02 March 2019 3,931 3 View
Before conducting our experiments we go for validation of our experimental setup with some known data sets. As we are also providing instrument errors and uncertainty analysis as well with our...
02 March 2019 9,975 5 View
We have observed that after heating up, mobile phones or desktop or laptop computers start performing slow. why is that? will the performance increase upon cooling the same device to cryogenic...
06 July 2018 7,154 3 View
If water in liquid jet or spray jet is changed with liquid ammonia, ethanol or petrol, then how the cooling effect will change on an impinging target. Please provide some literature or correlation.
06 July 2018 1,289 1 View
We are searching for a mathematical correlation for the droplets size distribution of liquid when atomized by air blast.
04 May 2018 4,637 3 View
A jet of air with added 1 percent of water by mass will have only a small volume of mixture occupied by the liquid phase. Although it can be assumed that the air water mixture have same viscosity...
03 April 2018 9,486 3 View
The nozzles used in the work of Quinn et al.,2017,Lyons et al.,2012 forms a re circulation zone near the nozzle exit. I am in search of authors and publications who did noticed this re circulation...
11 December 2017 6,763 0 View
I am Trying to model the flow of coaxial co flowing air atomized mist jet using Eulerian approach in ANSYS Fluent.whenever i try to run the VOF equation a patch velocity patch appears that lead...
07 August 2017 1,843 5 View
the actual size of the air molecule is somewhere in range of e-10 whereas from the avogadro law ,one molecule occupies about 3.3e-9 m of length.but both of the dimensions provide erroneous results...
09 October 2016 7,758 1 View
Dense DPM is used to track particles in the fluent simulations and do not have water liquid in the options of the particles.can we add water liquid in the model for Dense DPM?and how?
01 January 1970 3,949 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...
06 August 2024 6,728 6 View
Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)
05 August 2024 9,537 2 View
We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...
31 July 2024 4,510 3 View
Does anyone know of a module for the JAMOVI software that is capable of generating mean separations using the classic letters based on post hoc results (e.g., Tukey test)? If, as I believe, such...
31 July 2024 3,333 4 View
Hello everyone, I am currently using washed human platelets to stain Annexin V as a procoagulant marker. Additionally, I am staining with PerCP-CD61 to identify platelet cells. So far, I have...
29 July 2024 8,624 1 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
I cannot confirm cell surface protein expression by flow cytometry even after transfection and antibiotic selection of cells. Does it take long for proteins to express on the cell surface? the...
28 July 2024 3,178 3 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
