Can we use dense discrete phase model for air water spray in ansys fluent?

Vikash Kumar Singh Chauhan @Vikash_Chauhan3

01 January 1970 1 4K Report

Dense DPM is used to track particles in the fluent simulations and do not have water liquid in the options of the particles.can we add water liquid in the model for Dense DPM?and how?

Zoubair Boulahia

Look at this doc it may be helpul for your topic. Good luck.

Badges
Science topic

More Vikash Kumar Singh Chauhan's questions See All

What is Reacting Multiphase Flow Modeling?

How Reacting Multiphase flow model available with OPENFOAM is different from eulerian model of ANSYS Fluent? What are the governing equations and where can we find the closure schemes of various...

02 March 2019 3,931 3 View

Why do we Validate our experimental Setup?

Before conducting our experiments we go for validation of our experimental setup with some known data sets. As we are also providing instrument errors and uncertainty analysis as well with our...

02 March 2019 9,975 5 View

Why is the role of temperature on the performance of an electronic circuit?

We have observed that after heating up, mobile phones or desktop or laptop computers start performing slow. why is that? will the performance increase upon cooling the same device to cryogenic...

06 July 2018 7,154 3 View

What is the effect of changing the working fluid of jet on cooling effect on an impinging surface?

If water in liquid jet or spray jet is changed with liquid ammonia, ethanol or petrol, then how the cooling effect will change on an impinging target. Please provide some literature or correlation.

06 July 2018 1,289 1 View

What is the particle sizing when a liquid is atomized by pressurized gas?

We are searching for a mathematical correlation for the droplets size distribution of liquid when atomized by air blast.

04 May 2018 4,637 3 View

What should be the viscosity of Air Water Mixture?

A jet of air with added 1 percent of water by mass will have only a small volume of mixture occupied by the liquid phase. Although it can be assumed that the air water mixture have same viscosity...

03 April 2018 9,486 3 View

Which authors have studied the Re circulation Zone in co flowing external mixing two phase nozzles?

The nozzles used in the work of Quinn et al.,2017,Lyons et al.,2012 forms a re circulation zone near the nozzle exit. I am in search of authors and publications who did noticed this re circulation...

11 December 2017 6,763 0 View

How to model a co flowing mist jet of air and water impinging on a flat plate with Eulerian Model in Fluent?

I am Trying to model the flow of coaxial co flowing air atomized mist jet using Eulerian approach in ANSYS Fluent.whenever i try to run the VOF equation a patch velocity patch appears that lead...

07 August 2017 1,843 5 View

What is the diameter of the particles of the air for porous medium simulations in fluent?

the actual size of the air molecule is somewhere in range of e-10 whereas from the avogadro law ,one molecule occupies about 3.3e-9 m of length.but both of the dimensions provide erroneous results...

09 October 2016 7,758 1 View

What are the discrete phase and eulerian phase in ansys two phase model?

spray jet,nozzle

01 January 1970 5,189 0 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Are air moisture harvesting technologies effective in combating desertification?

Air moisture harvesting Air water collection devices

06 August 2024 5,473 2 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View