What are the differences between VOF model, Eulerian-Eulerian and mixture model in ANSYS FLUENT?

Som Dutt @Som_Dutt5

11 November 2018 0 521 Report

VOF model, Eulerian-Eulerian and mixture model in ANSYS FLUENT

Badges
Science topic

More Som Dutt's questions See All

Is any groups working on Development of photobioreactor and its design using Computational fluid dynamics (CFD) study and ANSYS Fluent in Australia ?

This Question is just to take an overveiw of labs work and for some suggestions regarding my work.

02 March 2018 1,317 0 View

How can I simulate the algal growth model in the bioreactor via using ANSYS FLUENT ?

For the study of light and bubble formation inside the PhotoBioreactor.

01 February 2018 3,020 6 View

How to write and insert the UDF of mathematical equations in ANSYSY Fluent ?

Specifically: Monod-type reaction for biomass growth calculations

01 February 2018 5,794 3 View

Is anybody using ANSYS Fluent for the Development of Bioreactor for the study of its computational fluid dynamics in Europe ?

For the designing modeling and the simulation pupose of bioreactor.

01 February 2018 3,477 2 View

Is anybody using ANSYS Fluent for the Development of Bioreactor for the study of its computational fluid dynamics in India ?

For the designing modeling and the simulation pupose

01 February 2018 4,543 2 View

How to write and insert the UDF in ANSYSY Fluent ?

Specifically: Monod-type reaction for biomass growth calculations

01 February 2018 6,137 4 View

Is anybody using ANSYS Fluent for the Development of Bioreactor for the study of its computational fluid dynamics ?

For the designing modeling and the simulation purpose of Bioreactor

01 February 2018 6,028 3 View

Is anybody using ANSYS Fluent for the Development of Bioreactor for the study of its computational fluid dynamics in U.S.A ?

For the designing modeling and the simulation purpose of Bioreactor.

01 February 2018 1,099 1 View

How to write and insert boundary conditions as UDF in ANSYSY Fluent ?

For a rectangular 2D geometry

01 February 2018 7,088 4 View

Can anybody tell any Research group working on related to computational investigation and modelling of Photo-bioreactor for Algal Growth in India

Research group

05 June 2017 2,722 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What analysis to choose with a large neste dataset and clearly skewed or kurtotic distributions?

Hello! I have a dataset of n=3000 nested within 8 countries with approximately 200 or 400 responses in each country. I originally planned to perform multilevel modelling with 4 dependent variables...

02 March 2021 6,865 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View