06 June 2017 0 3K Report

Research group

More Som Dutt's questions See All
What are the differences between VOF model, Eulerian-Eulerian and mixture model in ANSYS FLUENT?

VOF model, Eulerian-Eulerian and mixture model in ANSYS FLUENT

10 November 2018 567 0 View

Is any groups working on Development of photobioreactor and its design using Computational fluid dynamics (CFD) study and ANSYS Fluent in Australia ?

This Question is just to take an overveiw of labs work and for some suggestions regarding my work.

02 March 2018 1,457 0 View

How to write and insert the UDF of mathematical equations in ANSYSY Fluent ?

Specifically: Monod-type reaction for biomass growth calculations

01 February 2018 6,037 3 View

How can I simulate the algal growth model in the bioreactor via using ANSYS FLUENT ?

For the study of light and bubble formation inside the PhotoBioreactor.

01 February 2018 3,136 6 View

Is anybody using ANSYS Fluent for the Development of Bioreactor for the study of its computational fluid dynamics in Europe ?

For the designing modeling and the simulation pupose of bioreactor.

01 February 2018 3,597 2 View

Is anybody using ANSYS Fluent for the Development of Bioreactor for the study of its computational fluid dynamics in India ?

For the designing modeling and the simulation pupose

01 February 2018 4,660 2 View

How to write and insert the UDF in ANSYSY Fluent ?

Specifically: Monod-type reaction for biomass growth calculations

01 February 2018 6,261 4 View

Is anybody using ANSYS Fluent for the Development of Bioreactor for the study of its computational fluid dynamics ?

For the designing modeling and the simulation purpose of Bioreactor

01 February 2018 6,172 3 View

How to write and insert boundary conditions as UDF in ANSYSY Fluent ?

For a rectangular 2D geometry

01 February 2018 7,241 4 View

Is anybody using ANSYS Fluent for the Development of Bioreactor for the study of its computational fluid dynamics in U.S.A ?

For the designing modeling and the simulation purpose of Bioreactor.

01 February 2018 1,208 1 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Do we save MSMEs of the Nation ?

SMEs are backbone of the country's white economy, most of them are II generation entrepreneurs and migrated from family owned business policies, and having sufficient higher educations for...

01 August 2024 5,562 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close