UDF error :Error: receive a fatal signal (Segmentation fault)

01 January 2017 1 4K Report

i have compiled a UDF for htc at wall in ansys fluent. Once I initialize my solution, I am receiving the above error.

Any suggestion on how to resolve ?

please check your constants and variables in UDF file. your C file are compiled successfully but the constants have not been satisfied.

Badges
Science topic

More Sampath Emani's questions See All

Can anyone help me with the link of a book ?

Can anyone help me with the link of a book titled, "Computational Analysis of Multiphase Flow in a Helical Water-oil Separator Using CFD. Texas A&M" Authored by: Vijay Lakshmi .E

07 August 2018 9,612 0 View

Does increasing the tube length and decreasing the tube diameter, decreases the particles deposition ?

I have a fluid with few particles mixed. The fluid and the particles are flowing in a tube. I could see the particles are getting deposited on the tube surface. Now, i wish to decrease the...

02 March 2018 9,262 3 View

How can we induce shear on the wall surface of heat exchangers ?

Are there any ways to induce small amount of shear stress on the heat exchanger walls ? It can be done by increasing the velocity of the fluid and by increasing the surface roughness of the wall....

02 March 2017 5,191 7 View

Does porous-spongy like particles have shape factor ? If yes, may i know the range ? or calculation procedure ?

I heard that, particles with high roughness and solids have large shape factors and particles with irregular and spongy like will have smaller shape factors. Is this true ? Anyone have an idea of...

11 December 2016 5,385 2 View

What is the current advanced research in the field of oil and gas for performing computational simulations?

As oil and gas field is one of emerging field all over the globe,Seeking to know the current computational research which is much into interest in the field of oil and gas

09 October 2013 2,594 2 View

Can I get any case study related to liquid seal drum CFD analysis ?

Flare system, flare gas glow through water seal drum.

09 October 2013 922 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

When you express a protein, why do we express not only the domain we want, but also the protein around it?

I want to express STK4, and I've searched the paper for reference. When I check the protein kinase domain sequence for that kinase on Uniprot, it's 30-281, but the paper expresses the protein...

20 July 2024 4,951 1 View

What will be the best way to test NFkb activation via western blot?

Hi, I have lysate from human macrophages, and I wonder what will be the best way to check the NFKB activation in those cells. I was thinking p-p65 or p-ikkb./ Is that make sense?

18 July 2024 5,214 4 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

Does anyone know how to improve calcium-imaging fluorescence with GRIN lenses?

Hey everyone, I've been working with GRIN lenses (Inscopix) for almost 1 year and still had no luck seeing strong fluorescence on them. When I look at them, I can see good blood flow and,...

08 July 2024 5,178 2 View