Does increasing the tube length and decreasing the tube diameter, decreases the particles deposition ?

I have a fluid with few particles mixed. The fluid and the particles are flowing in a tube. I could see the particles are getting deposited on the tube surface. Now, i wish to decrease the...

02 March 2018 9,128 3 View

How can we induce shear on the wall surface of heat exchangers ?

Are there any ways to induce small amount of shear stress on the heat exchanger walls ? It can be done by increasing the velocity of the fluid and by increasing the surface roughness of the wall....

02 March 2017 5,075 7 View

UDF error :Error: receive a fatal signal (Segmentation fault)

31 December 2016 3,924 1 View

Does porous-spongy like particles have shape factor ? If yes, may i know the range ? or calculation procedure ?

11 December 2016 5,265 2 View

What is the current advanced research in the field of oil and gas for performing computational simulations?

As oil and gas field is one of emerging field all over the globe,Seeking to know the current computational research which is much into interest in the field of oil and gas

09 October 2013 2,490 2 View

Can I get any case study related to liquid seal drum CFD analysis ?

Flare system, flare gas glow through water seal drum.

09 October 2013 824 1 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Could you recommend any books about Number Theory?

Beginner level books. High level books. Analytical Number Theory. Algebraic Number Theory. Combinatorical Number Theory. Books about partitions. Books about primes.

03 March 2021 7,174 5 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View