How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

Any suggestion for conductive paste for PDMS or Ecoflex for electrode?

Dear colleagues, I am trying to make a sturdy electrode on a flexible polymer substrate (PDMS or Ecoflex). I have used a silver paste, but once cured, it peels off very easily. the cured silver...

14 December 2020 4,236 3 View

What is the best way to isolate proteins which are located in the endosomes and the ER membrane?

For one of my projects, I need to perform WBs on cell lysates. The protein of interest (LRAT) is located in the endosomes and the membrane of the ER. What is the best protocol to isolate proteins...

25 November 2020 969 3 View

Can I autoclave d-mannose?

Hello everyone, I was wondering whether I should autoclave or filter d-mannose solution. In our laboratory, we autoclave glucose separately when we make YPD media for yeast culture. So, I am...

08 October 2020 7,068 1 View

How to increase the signal of the protein standard when performing western blot?

Hi, I'm writing my master's thesis on the characterization of human proteins which I express and purify from E. coli. I'm performing western blot to verify my protein, but the protein standard...

06 October 2020 1,107 5 View

Does topology from ATB support FF other than Gromos?

I am new to MD / gromacs and I am trying to use MD not for biological system but for generic materials science. Specifically, I am trying to simulate the interaction between hydrophobic molecules...

07 June 2020 8,989 2 View

How can I use a molecule from ATB in Gromacs?

I am new to MD / gromacs and I am trying to use MD not for biological system but for generic materials science. Specifically, I am trying to simulate the interaction between hydrophobic molecules...

06 June 2020 2,112 4 View

Does anyone know about analysis of 3D mapping and depth profile for wooden object?

I have 1cm cubic size wood samples. inside of wood, there are S and S-organic, inorganic compounds randomly. I'd like to figure out the quantities of S distribution non-destructively. First, I...

20 February 2020 9,303 2 View

Is there any atmosphere that Titanium chloride can make fume?

I use TiCl4 to check if there's water in the glovebox. when I opened TiCl4 there were a lot of fumes, but I never guess where the water comes. Because there was no oxygen inside. So I didn't sure...

13 January 2020 9,127 1 View

Is it viable to replace ray-traced 3d simulation visualization with Neural network (say GAN)?

My problem may not be very general. Imagine you observe the sun through thick clouds in multiple wavelengths. Given the spectrum of light starting off the sun's surface, you can calculate how rays...

08 January 2020 4,764 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

No title

02 March 2021 3,060 3 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View