How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

Can I calculate the average from the data which are collected every 30 minutes for ANOVA?

I artifically elevated the air temperature in the heated plot by 3-celsius degree compared to that in the control for 7 days. I want to figure out the effect of the temperature manipulation on...

21 January 2021 1,185 8 View

How much the nanoparticles reach the inflammatory tissue?

Dear colleagues, I want to know the average analysis data of EPR effect on inflammatory tissue (acute lung inflammation/injury, ischemia/reperfusion, rheumatoid arthritis, and sepsis..) In...

22 December 2020 3,147 2 View

Any suggestion for conductive paste for PDMS or Ecoflex for electrode?

Dear colleagues, I am trying to make a sturdy electrode on a flexible polymer substrate (PDMS or Ecoflex). I have used a silver paste, but once cured, it peels off very easily. the cured silver...

14 December 2020 4,236 3 View

How to measure the bonding strength of transfered graphene on PDMS substrate?

Chemical vapor deposition (CVD) was used to grow graphene on copper (Cu ) substrate, then the single layer graphene was transfered onto a PDMS substrate. I want to measure the bonding strength of...

17 October 2020 3,567 3 View

How to calculate bulk density, porosity, and void ratio of soil?

If the particle diameter is 2 mm and the particle density is 2.5 g/cm, what is the bulk density, porosity, and void ratio of this soil? I had known that the formula to calculate them. The...

11 October 2020 3,466 3 View

Can I autoclave d-mannose?

Hello everyone, I was wondering whether I should autoclave or filter d-mannose solution. In our laboratory, we autoclave glucose separately when we make YPD media for yeast culture. So, I am...

08 October 2020 7,068 1 View

How to define the particle agglomeration in composite materials or foundry alloys and measure its size distribution quantitatively?

28 June 2020 7,614 3 View

Does topology from ATB support FF other than Gromos?

I am new to MD / gromacs and I am trying to use MD not for biological system but for generic materials science. Specifically, I am trying to simulate the interaction between hydrophobic molecules...

07 June 2020 8,989 2 View

How can I use a molecule from ATB in Gromacs?

I am new to MD / gromacs and I am trying to use MD not for biological system but for generic materials science. Specifically, I am trying to simulate the interaction between hydrophobic molecules...

06 June 2020 2,112 4 View

I am interested in medicinal chemistry field, which books are highly recommended to learn from?

I am at the beginner level in drug design and drug discovery, and I am interested to learn more about this field. Which books are highly recommended to start from and gives me all essential...

02 March 2021 8,437 2 View

Compact antenna for the frequency range 1 MHz-5 MHz?

Hello everybody! I have a problem with developing a compact antenna for the 1MHz-5MHz frequency range. Tell me what type of antenna can be used and what books and articles to read to perform this...

27 February 2021 7,710 4 View

Any specific pipeline or parameter to analyse total transcriptomics study of brain tissue samples?

I have two groups of brain samples, control and treated for example. It was total RNA nova seq sequencing. I tried all the available pipeline like: star+rsem+deseq2, Hista+stringtie+cuffdiff,...

27 February 2021 356 6 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

How to construct different filler shape in MD simulations?

Is there any way to construct different initial filler shapes like triangle, square, rectangle, pillar, and tube in any simulation software.

20 February 2021 1,750 1 View

Access to supercomputer resources in India?

Hello everyone, I want to perform some gaussian calculations and want to use Materials studio for my research work. Can anyone guide me how to get access to supercomputer resources in India for...

15 February 2021 8,264 3 View

Do you know of an informal caregiver of a person who has recently received a bone marrow transplant?

We are conducting a pilot study of an intervention for informal caregivers of persons who have recently received a bone marrow transplant in the US. If you know of anyone who might be interested,...

13 February 2021 9,174 1 View

Can we have constructs of Cronbach alpha value with more than 0.9 in social science research? What is recommended in this problem?

My study consists of a conceptual framework with seven constructs measured in seven point Likert scale. According to pilot study, only three constructs have Cronbach alpha value more than 0.9...

12 February 2021 9,368 2 View

Is there a way to use waveguide ports for circular antenna design in CST?

Hi, whenever i use circular array i get this error "Waveguide ports must be aligned with Cartesian coordinate planes for the transient solver" Does anyone use circular array with waveguide ports?...

09 February 2021 3,609 8 View