are the unit cell parameters changeable with T? I need a reference
Dear Tamara V Gavrilovic ,
for the thermal expansion of Y2Mo3O12*) you may have a look at:
Article Thermal Expansion Behavior in the A2M3O12 Family of Materials
(Table 1 at page 5)
Ref 68 therein may give further details.
Unfortunately Eu2Mo3O12, as you asked for in a similar question, is not mentioned there...
*) you may have a typing error in your chemical formula (Mo2 instead of Mo3)
Good luck and
best regards
G.M.
Dear all, we have been running multiple ddRAD libraries prepared by following the protocol of Petersen et al 2014 in our lab on the HiSeq2500 (SR 100) in the past couple of years. We pooled...
28 September 2020 2,297 1 View
Hello, I have the following question on paired end reads from RNA-seq: To get the total number of obtained reads from paired end reads (2 fastq files are generated (R1, R2), is it correct to add...
01 September 2020 7,715 5 View
13 August 2020 8,401 3 View
Hello! I'm trying to perform a TaqMan qPCR to check for certain fish species in environmental DNA samples. I am using a published primer + probe set. The probe is carrying FAM at it's 5' end and...
14 April 2019 4,907 15 View
I need some guidance on selecting the appropriate statistical methods for my research. I am investigating lone violent extremists by subtype (far right, far left, Islamic and single-issue) on 4...
11 May 2018 1,809 3 View
18 December 2014 1,476 6 View
Hello Everyone I tried to differentiate Embryoid bodies (EBs) from mouse Embryonic Stem cells (E14tg2a) following the protocol I attached. However i failed during the process because despite cells...
01 January 1970 155 6 View
Working on a behavioral therapy protocol and looking for a psychometric assessment tool to measure maturity in adolescents and young adults up to 24 years in age.
01 January 1970 3,684 7 View
Hello, I have an excel sheet with microsatellite data, I would like to make a NJ tree out of it. I have a basic level in bioinfo. Can someone please guide me through the steps to get the...
01 January 1970 6,828 2 View
03 March 2021 8,272 1 View
In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?
01 March 2021 1,923 3 View
Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.
28 February 2021 3,640 3 View
Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...
26 February 2021 1,100 5 View
Hi, my question is about the heating of thermal cycler machines and I hope some of you had experienced a similar thing previously. There are two thermal cycler machines in the lab(BioRad) and for...
26 February 2021 4,777 4 View
I am working with Polyacrylic acid (100.000Da) and instead of water, I need to use another solvent (dioxane) to dissolve PAA. However, because of the high molecular weight, it's quite hard to...
25 February 2021 2,225 5 View
I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...
23 February 2021 2,390 3 View
I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...
23 February 2021 4,155 4 View
23 February 2021 9,253 1 View
I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?
22 February 2021 5,915 3 View