Suction pump of the Rotary evaporator?

More Fasan Israel's questions See All

What significance is the following?

What is the significance of the following solutions being used as rodent"s organ fixatives, between normal saline, citrate buffer and sucrose?

06 July 2019 8,472 1 View

Defat before phenolic rich fraction extraction?

03 April 2019 7,977 9 View

Administration dose to animals??

Can someone explain the best way to determine the dose of extract to be administered to experimental animals in evaluating its potency ? Your response will be highly appreciated.

03 April 2019 6,013 3 View

How do someone perform qualitative analysis of terpenoids?

how can qualitative analysis of terpenoid extracted from plants be performed?

02 March 2019 3,246 7 View

What are the possible ways of measuring the blood pressure of rodents?

Possible and best methods to measure the blood pressure of rats.

02 March 2019 333 3 View

How to remove fatty material from plant extract?

The resultant solid was partitioned three times with 250 ml of petroleum ether (40-60/c) to remove any fatty material and evaporated to dryness.

28 February 2021 9,464 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How the wettability of rock sample can be changed by ageing in pure hydrocarbon oils only?

I want to do wettability analysis of hydrocarbon oil (octane)/rock/surfactant solution system. but to do the analysis first I have to make rock surface oil-wet. Since hydrocarbon oil does not have...

27 February 2021 5,383 3 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

Has anyone experienced changes in growth for cell culture when purchasing media from different companies?

I recently switched the company where we buy our DMEM/F12 and i have noticed a signficant change in growth for my human olfactory neurosphere cell lines

24 February 2021 2,268 3 View

How can Gamma Ray API units be converted to CPS (counts per second)?

Oil and gas companies run gamma ray tool and take readings in API units while Gamma ray is also noted in cps, so how these units can be converted into each other?

24 February 2021 7,545 2 View

How to remove compound ( Europium complex ) from paraffin oil?

How can I remove my compound from paraffin oil? Mistakenly my compound fell in an oil. Compound = Europium complex

22 February 2021 5,667 2 View

When I mix oil and NaOH solution, Why solid layer in the surface is formed?

During my trial for lubricant oil re-refinery process, I use NaOH as coagulant agent. After overnight of gravity settling, a solid layer in the surface was form. what product is that? since the...

22 February 2021 2,116 4 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View

The type of filter paper used to filter an epoxidized oil (the mixture is an epoxidized oil with magnesium sulfate) ?

I have a mixture of epoxidized oil and magnesium sulfate wich type of filtre paper should i use

21 February 2021 3,944 3 View

Grzegorz Boczkaj

Solvent is volatile - in under pressure conditions it will evaporate in some part to your pump.

Before you turn off the pump - you should first pressurize the system - i.e. open a dedicated valve and allow to get an atmospheric pressure in your system - after that you can turn off the pump.

regards,

Fasan Israel

Well articulated reply and Much appreciation to Dr. Grzegorz.

Thanks

Dr. Grzegorz,

Moreover, that has been done and it didn't prevent the suction of the solvent into the pump and eventually to the oil. Afterward, the pump oil do have the odour of the solvent being recovered. Nonetheless, any other suggestion will be highly appreciated.

Regards

Fasan,

so you need to install a filter before the pump - It could be a column with activated carbon or a crio-condenser.

Secondly - if you don't need a very high vacuum you can replace the oil pump by a simple water pump.

Thanks. Moreover, what type of condenser can I use and i will be very glad if you can send the picture here or to [email protected].

More so, I even added bushner flask immerse in cold water chilled with ice block, just before the pump to further condense the organic vapour. However, the accumulated odour at the pump and the oil just decreased.

Hope, water pump with an outlet to the surrounding might be the best professional advice as suggested.

My sincere regards oncemore.

Sorry I mean filter not condenser.

What can of filter can I use?

Thanks.

Take any column - glass or SS put there activated carbon, connect it inline.

Thanks so far. Moreover, what is the minimum power or rpm of the water pump that is most advisable.

Regards.

Check this one:

https://www.fishersci.co.uk/shop/products/azlon-polypropylene-water-jet-vacuum-pump/11986858

Thanks. However, I guess, the water pump with an outlet to the surrounding medium will be better in application to the foregoing adventure rather than the non return valve as suggested.

Perhaps, the organic vapour under suction, will be released to the surrounding by the water pump, while the one way valve will only and still by pass the organic vapour into the pump.

Nevertheless, any suggestion is highly welcome.

Love you.

............by pass the organic vapour into the present suction pump?

I thought, if there are no water for water pump to suck rather organic vapour, might eventually burn the water pump.

Just curious before buying .

Moreover, any suggested model of water pump will be highly appreciated.