Hi, can we get the steady state solution directly of TPCT in Ansys / Fluent ?
Or, we should use transient solution till reach the final steady state ?
https://www.sciencedirect.com/search?qs=Two-phase%20closed%20thermosyphon%20steady%20state&show=25&sortBy=relevance
Thanks allot Md. Washim Akram .
But, I'm not looking for CFD solution setup for TPCT.
My question is " could we get steady state solution directly or not?".
the steady state solution can be obtained by solve the governing equations for steady flow directly. This solution (same solution) also can be obtained by solve the unsteady governing equations after reach steady (for a long certain time).
Thanks for your answer Laith M. Jasim , so , can we get steady state solution directly in Fluent? Or not.
certainly.
Hello , for which percent we can trust in numerical solution results for energy and fluid flow problems in Fluent , Comsol , ... etc ? Please verify the percentage for which software.
31 December 2018 10,151 7 View
Hello , can we simulate the fluid flow sounds in Fluent? i.e. when we get a recorded transient solution , can we get the related sounds of fluid flow for this solution ?
31 December 2018 2,475 12 View
Hi, how could I change the background color to white instead of blue in Ansys R 19 ?
10 November 2018 11,170 8 View
Hi After finishing the calculation in fluent . How could I get convection heat transfer coefficient at a specific face or area?
08 September 2018 3,379 7 View
Hello , I'm need calculations and modeling procedures for design a heat pipe with minimum error percentages in transit and steady state . Also modeling code in Matlab will be help...
02 March 2018 3,220 0 View
Does we work with high or low pressure of vapor inside loop heat pipe ...? which magnitudes ?
01 February 2018 9,774 0 View
Hi, in some transient solution cases in Fluent , after thausands of time steps , not limited , the updating of solution time step to start the iteration of the next time step take a long time,...
01 January 1970 9,892 13 View
Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...
11 August 2024 8,141 3 View
"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....
10 August 2024 8,621 1 View
Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...
10 August 2024 8,992 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...
08 August 2024 6,134 12 View
Hello experts, Does anyone know any free software about retention index prediction ?
08 August 2024 7,403 2 View
I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...
08 August 2024 8,329 0 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...
07 August 2024 269 3 View