How much pressure can reached in a loop heat pipe?

02 February 2018 0 10K Report

Does we work with high or low pressure of vapor inside loop heat pipe ...? which magnitudes ?

Badges
Science topic

Similar topics
Thermodynamics
Pressure

More Alaa Temimy's questions See All

Trust in energy and fluid flow problems numerical solutions ?

Hello , for which percent we can trust in numerical solution results for energy and fluid flow problems in Fluent , Comsol , ... etc ? Please verify the percentage for which software.

31 December 2018 9,984 7 View

Fluid flow sounds in Fluent?

Hello , can we simulate the fluid flow sounds in Fluent? i.e. when we get a recorded transient solution , can we get the related sounds of fluid flow for this solution ?

31 December 2018 2,341 12 View

Ansys white color background ?

Hi, how could I change the background color to white instead of blue in Ansys R 19 ?

10 November 2018 9,302 8 View

Steady state solution for Two-phase closed thermosyphon heat pipe?

Hi, can we get the steady state solution directly of TPCT in Ansys / Fluent ? Or, we should use transient solution till reach the final steady state ?

10 November 2018 8,082 5 View

Convection heat transfer coefficient in fluent?

Hi After finishing the calculation in fluent . How could I get convection heat transfer coefficient at a specific face or area?

08 September 2018 3,197 7 View

Heat pipe design calculations ?

Hello , I'm need calculations and modeling procedures for design a heat pipe with minimum error percentages in transit and steady state . Also modeling code in Matlab will be help...

02 March 2018 3,082 0 View

Transient solution time in Fluent ?

Hi, in some transient solution cases in Fluent , after thausands of time steps , not limited , the updating of solution time step to start the iteration of the next time step take a long time,...

01 January 1970 9,736 13 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View