Heat pipe design calculations ?

03 March 2018 0 3K Report

Hello , I'm need calculations and modeling procedures for design a heat pipe with minimum error percentages in transit and steady state .

Also modeling code in Matlab will be help full.

Thanks to all.

Badges
Science topic

Similar topics
Engineering
Modeling

More Alaa Temimy's questions See All

Trust in energy and fluid flow problems numerical solutions ?

Hello , for which percent we can trust in numerical solution results for energy and fluid flow problems in Fluent , Comsol , ... etc ? Please verify the percentage for which software.

31 December 2018 10,151 7 View

Fluid flow sounds in Fluent?

Hello , can we simulate the fluid flow sounds in Fluent? i.e. when we get a recorded transient solution , can we get the related sounds of fluid flow for this solution ?

31 December 2018 2,475 12 View

Ansys white color background ?

Hi, how could I change the background color to white instead of blue in Ansys R 19 ?

10 November 2018 11,170 8 View

Steady state solution for Two-phase closed thermosyphon heat pipe?

Hi, can we get the steady state solution directly of TPCT in Ansys / Fluent ? Or, we should use transient solution till reach the final steady state ?

10 November 2018 8,228 5 View

Convection heat transfer coefficient in fluent?

Hi After finishing the calculation in fluent . How could I get convection heat transfer coefficient at a specific face or area?

08 September 2018 3,379 7 View

How much pressure can reached in a loop heat pipe?

Does we work with high or low pressure of vapor inside loop heat pipe ...? which magnitudes ?

01 February 2018 9,774 0 View

Transient solution time in Fluent ?

Hi, in some transient solution cases in Fluent , after thausands of time steps , not limited , the updating of solution time step to start the iteration of the next time step take a long time,...

01 January 1970 9,892 13 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View