Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Do anyone here can help us in the field of molecular docking?

We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...

01 March 2021 1,899 2 View

Analysis of CRD two factor using R studio ?

Hello everyone. I have conducted the research on post harvest longevity of tomato crop using plastic packaging and different doses of chemicals as two different factors. The design of experiment I...

28 February 2021 8,189 3 View

What is the exact mechanism of the antimicrobial effect of local anesthetics?

The antimicrobial effect of local anesthetics has been known for more than 50 years, but it still seems to have an unclear mechanism of action. which bacteria? which concentration? etc etc. ....

27 February 2021 4,450 2 View

How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

Resistivity of PVD TiNx thin films vs. N2 flow?

In the PVD of TiN thin films (~100A), I've found the resistivity of the TiN films dropped from ~100 to 60um*cm with N2 flow increasing up to the metallic mode ending point; then the resistivity...

21 February 2021 1,864 2 View

What are your alternative data collection methods during the pandemic? What are the pros and cons?

Dear colleagues We are exploring possible data collection methods for environment and behavior research in the context of architectural environments. Have you conducted any Post Occupancy...

16 February 2021 2,575 4 View

Can bio-decomposer be a successful alternative to reduce residue burning?

To maintain the proper crop plan most of the times there is not enough time to make the field ready for the next crop. In this particular context , can bio-decompser be a solution? What about...

16 February 2021 7,068 24 View

Is there any effective FEM solver to perform simulation of balloon inflation with large deformation (e.g. 300% strain)?

Hi! Thank you for your time, attention, and support. I am currently using FEM solver Abaqus to perform a set of balloon inflation simulations, trying to understand the deformation shape, stress,...

14 February 2021 2,524 4 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View