I am trying to simulate friction stir welding using coupled eulerian lagrangian method in abaqus 6.11. Though tool is moving inside the material but mesh is not deforming. kindly see the attach pictures.
Can you share your model to look at it and tell you what might go wrong? You can send me a private message if you want.
Send me your cae file please. I will check it.
[email protected]
I am modeling FSW in ABAQUS/Explicit using Coupled Eulerian and Lagrangian method. In post processor when I am unable to apply multiple cut in view cut manager if one of the cut is EVF void. I...
09 October 2016 3,080 4 View
Hey!!I need to multiply viscous dissipation/heating term with a factor of 0.4( or say is as efficiency factor) and the resulting term should be further used as effective viscous dissipation term...
05 June 2016 8,831 14 View
I working in the area of modeling friction stir welding process in ANSYS FLUENT. I am assuming it as steady state analysis. In literature, I have seen many researchers assuming the process as...
05 June 2016 5,727 4 View
I am working on simulation of friction stir welding in DEFORM 3D. Sometimes nodal velocity of workpiece shoots to a high value (which is practically not feasible) leading to convergence issue. Is...
04 May 2016 4,392 1 View
I am modelling friction stir welding process in ANSYS fluent as a steady state analysis but the solution is not converging. I have taken workpiece as a rectangular block and defined no slip...
04 May 2016 2,941 2 View
I am trying to simulate friction stir welding using coupled eulerian lagrangian analysis in ABAQUS 6.11. Wheneve I define johnson cook plasticity model the simulation aborts but if I choose...
07 August 2015 4,719 1 View
Hi I am trying to simulate FSW using CEL method in ABAQUS. But as soon as I used coupled thermal element, simulation aborts showing an error "abaqus/explicit has excited with an error" But when I ...
07 August 2015 1,701 2 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View