I am modelling friction stir welding process in ANSYS fluent as a steady state analysis but the solution is not converging.
I have taken workpiece as a rectangular block and defined no slip condition.
Convergence criteria is taken as 10-6 for energy
You are requested to check the mesh sensitivity, time-time stepping and boundary conditions used.
Thank you for your kind reply. I have tried different mesh size but with no result. I have attached mesh size and convergence picture here.
I have also tried for running simulation first for constant viscosity for initial iteration and then switch to UDF.
Any suggestion and help will be appreciated
I am modeling FSW in ABAQUS/Explicit using Coupled Eulerian and Lagrangian method. In post processor when I am unable to apply multiple cut in view cut manager if one of the cut is EVF void. I...
09 October 2016 3,080 4 View
Hey!!I need to multiply viscous dissipation/heating term with a factor of 0.4( or say is as efficiency factor) and the resulting term should be further used as effective viscous dissipation term...
05 June 2016 8,831 14 View
I working in the area of modeling friction stir welding process in ANSYS FLUENT. I am assuming it as steady state analysis. In literature, I have seen many researchers assuming the process as...
05 June 2016 5,727 4 View
I am working on simulation of friction stir welding in DEFORM 3D. Sometimes nodal velocity of workpiece shoots to a high value (which is practically not feasible) leading to convergence issue. Is...
04 May 2016 4,392 1 View
I am trying to simulate friction stir welding using coupled eulerian lagrangian method in abaqus 6.11. Though tool is moving inside the material but mesh is not deforming. kindly see the attach...
07 August 2015 2,988 2 View
I am trying to simulate friction stir welding using coupled eulerian lagrangian analysis in ABAQUS 6.11. Wheneve I define johnson cook plasticity model the simulation aborts but if I choose...
07 August 2015 4,719 1 View
Hi I am trying to simulate FSW using CEL method in ABAQUS. But as soon as I used coupled thermal element, simulation aborts showing an error "abaqus/explicit has excited with an error" But when I ...
07 August 2015 1,701 2 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View