Should i use universal buffer pH=2:12 when i add only 1 uL of HCl or NaOH to 2 mL solution in cuvette?

More Muhammad Khattab's questions See All

How combine yolo with Faster R-CNN?

I want a model that is balanced with accuracy or speed, faster rcnn has high accuracy while yolo have fast speed. i am thinking to combine them to get a hybrid model to achieve both speed and accuracy

02 August 2024 3,104 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Addition of EDTA during the synthesis of copper nanoparticles to prevent it from being oxidized?

I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...

28 July 2024 8,027 3 View

Can I please ask why my samples from anaerobic bioreactor giving me different size PCR product even after multiple runs?

Hi everyone, I have extracted DNA from a biogas bioreactor using Qiagen kit and prep cDNA library then used this library as template to optimize primers for qPCR (taken from papers). Some of the...

23 July 2024 1,329 5 View

Swerling Characteristic functions?

Hello!!! I want to implement the Swerling characteristics functions (CF) directly in MATLAB without using its Fourier integral pairs...the Swerling CFs are actually Laplace Transform of the signal...

23 July 2024 4,925 1 View

Radar Detection Probabilities?

Currently I need to calculate detection probabilities (PD) from RCS data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0 Equation. The idea is based on...

22 July 2024 2,851 0 View

Why methanol and sulphuric acid used in the analysis of polyhydroxyalkanoates (PHA) by GC-MS?

Why methanol and sulphuric acid, used in the analysis of polyhydroxyalkanoates (PHA) methyl esters by GC-MS? Additionally, why do we typically use non-polar solvents in GC-MS?

22 July 2024 1,210 2 View

Radar Detection Probabilities using beta distributed Scattering Cross section?

Currently I need to calculate detection probabilities (PD) from radar cross section (RCS) data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0...

22 July 2024 868 0 View

I want to buy Hydrothermal Synthesis Autoclave from any European company. Can anyone suggest any company inside Europe?

Thanks

22 July 2024 1,143 3 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

AMAXA Lonza nucleofection lower volume of buffer?

Does anyone tried to do nucleofection with AMAXA by Lonza with lower than recommended amount of buffer in the cuvettes (100 ul)?

07 August 2024 4,616 0 View

Why I can't see any band in SDS-PAGE?

Currently, when I run SDS-PAGE, I don't see any bands at all, even though I used the same material just a day ago and it worked fine.... In our lab, we dilute the 10X running buffer to 1X and...

06 August 2024 5,373 2 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

What is the best blank for nanodrop if I want to read a recombinant protein concentration?

Is it the "elution buffer" or the "dialysis buffer"? Note: I'll be using NanoDrop OneC

01 August 2024 967 3 View

What is the best practice for resuspending cell pellets during competent cell preparation (both electro and comp)?

I'm fairly new to making homemade comp cells and have done so with some mild success. What is generally an acceptable way of resuspending comp cells during wash steps? I've been told to swirl the...

31 July 2024 8,309 0 View

EDTA buffer solution?

Hello everyone! How can i prepare EDTA buffer solution (pH 8.2) to determine GSH levels? Thank you in advance.

29 July 2024 4,374 1 View

Whether i can preserve leaves samples in 2.5% glutaraldehyde in 0.05 M phosphate buffer, pH 7 for coming several weeks for further LM study ?

I want to preserve the sample leaves for the LM study of the stomata and conidia analysis. Whether 2.5% glutaraldehyde in 0.05 M phosphate buffer with pH 7 can be applied for preservation.

29 July 2024 8,560 0 View

What is the best method for removing paraffin from plant samples prepared for microtome?

...

24 July 2024 3,087 3 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

How can EDTA be removed from already extracted DNA samples?

Our lab has extracted bacterial DNA samples using Qiagen DNeasy kit and eluted the samples in AE buffer. However, this buffer contains 0.5mM EDTA not suitable for downstream application. Any ideas...

13 July 2024 1,675 3 View