Fatigue analysis on ANSYS Mechanical APDL
@M Mesbah
Thank u for your research
You have to use Ansys workbench module to calculate design fatigue life analysis, It accumulates the damage from repeated loading to predicted the life of component.
Even when synthesized under optimized conditions, the band gap of green-synthesized CuO nanoparticles (NPs) may fall outside the typical range of 1.20 - 2.62 eV. The energy band gap of these...
12 April 2024 6,439 0 View
I am working on BD FACSCanto II machine. When I started the machine, the fluidic start up is not successfully completed. It says failed. Can anyone give me some clue to solve the problem? Thank you!
03 February 2024 8,554 0 View
Hi, I have monthly precipitation and monthly temperature (not classified as minimum and maximum). How can I calculate SPEI index using Rstudio? I have also additional inputs like year, months and...
14 April 2023 8,672 2 View
The ASTM 3039 suggested a preparation of composite specimen for tensile test should be as per what i attached here....like it encourages 4methods based on fiber orientation. For 0 degeree fiber...
06 February 2021 9,852 5 View
can i pool cohort and case-control together in a meta analysis of risk factor??
24 May 2020 7,033 0 View
I ran PCR to amplify lpxA gene of Campylobacter so as to detect Campylobacter jejuni and Campylobacter coli. However, I faced repeated primer dimer formation but no band was formed for my target...
06 April 2020 5,800 22 View
I was studying plot-based comparison of two treatments regarding their contribution to sediment response. the slope is also another factor going to consider in the field experiment. the plot is...
24 March 2020 5,967 3 View
I have principally two treatments and two blocks with different slope. the total experimental and control groups are 12 plots and they have same experiemtal units. Both blocks B1 and B2 will have...
10 February 2020 295 0 View
Soil improvers are those which are improving the soil structure and stimulates the development of a diverse and rich microbial soil life. Here, I am not using soil but red ash (fine gravel) which...
21 October 2019 9,214 4 View
Project Partial replacement of waste glass and ceramic as coarse aggregate to produce c-25mpa concrete
22 December 2018 6,464 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,047 2 View
Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)
03 August 2024 8,537 4 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,031 2 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
It has been documented that apoptotic cells themselves can induce phosphorylation of serine 139 on H2AX (γH2AX) due to DNA fragmentation during apoptosis (doi: 10.1074/jbc.275.13.9390). As γH2AX...
28 July 2024 7,983 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
How the damages of building and shopping centers affected the south African economy?
24 July 2024 5,400 2 View
Hello, I'm planning a shell exchanging experiment with two marine, hermit crab species inside of a tank. I only have one tank available for this experiment. I plan on running 30-40 shell...
20 July 2024 5,676 3 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
Hello, I am an Etch Engineer. I am performing etching with high T_ox/Nit selectivity using remote plasma. Etching plasma is formed using only NH3/NF3/H2. 1. I wonder if it would be advantageous...
11 July 2024 8,113 2 View