Can anyone help me?

04 February 2024 0 9K Report

I am working on BD FACSCanto II machine. When I started the machine, the fluidic start up is not successfully completed. It says failed. Can anyone give me some clue to solve the problem?

Thank you!

Badges
Science topic

Similar topics
Social Psychology
Attitude

More Yohannes Zenebe Chekol's questions See All

Even if it was synthesized under optimized conditions, is the band gap of the green synthesized CuO NPs outside the typical range of 1.20 - 2.62 eV?

Even when synthesized under optimized conditions, the band gap of green-synthesized CuO nanoparticles (NPs) may fall outside the typical range of 1.20 - 2.62 eV. The energy band gap of these...

12 April 2024 6,439 0 View

I want to upload my research article ?

I've a research article published in a journal, i want to upload my research article on research gate , how can id do that ?

11 January 2024 9,526 2 View

Hi, I have monthly precipitation and monthly temperature (not classified as minimum and maximum). How can I calculate SPEI index using Rstudio?

Hi, I have monthly precipitation and monthly temperature (not classified as minimum and maximum). How can I calculate SPEI index using Rstudio? I have also additional inputs like year, months and...

14 April 2023 8,672 2 View

Please send me ANSYS Mechanical APDL Fatigue analysis codes investigate outputs such as fatigue life, damage, safety factor, sensitivity and biaxalty?

Fatigue analysis on ANSYS Mechanical APDL

02 June 2021 4,393 2 View

Why ASTM 3039 standards for specimen geometry focus on the fiber orientation and why not on the materials type,composition and manufacturing method?

The ASTM 3039 suggested a preparation of composite specimen for tensile test should be as per what i attached here....like it encourages 4methods based on fiber orientation. For 0 degeree fiber...

06 February 2021 9,852 5 View

Is that possible to pool odds ratio and relative risk together in a meta analysis?

can i pool cohort and case-control together in a meta analysis of risk factor??

24 May 2020 7,033 0 View

Dear all, can any one help me how to avoid primer dimer formation?

I ran PCR to amplify lpxA gene of Campylobacter so as to detect Campylobacter jejuni and Campylobacter coli. However, I faced repeated primer dimer formation but no band was formed for my target...

06 April 2020 5,800 22 View

How could I take sampling of sediment concentration from runoff collecting tank?

I was studying plot-based comparison of two treatments regarding their contribution to sediment response. the slope is also another factor going to consider in the field experiment. the plot is...

24 March 2020 5,967 3 View

Should i use random block design when assigning the treatments inside the block?

I have principally two treatments and two blocks with different slope. the total experimental and control groups are 12 plots and they have same experiemtal units. Both blocks B1 and B2 will have...

10 February 2020 295 0 View

How can soil improvers help my crops where the growing media is red ash (fine gravel)?

Soil improvers are those which are improving the soil structure and stimulates the development of a diverse and rich microbial soil life. Here, I am not using soil but red ash (fine gravel) which...

21 October 2019 9,214 4 View

Is there any machine to do real time pcr?

I want to know how do you make real time pcr solation ? is there any machine to make it? thanks for answering

05 August 2024 1,658 0 View

Is it necessary to attach fluorophore at 3' end in MIC RT PCR machine for Dual hybridization Probe designed especially for genotyping assay?

I designed 2 dual hybridization probes for my single SNP. where I attach my fluorophore 5'-FAM-nnnn-BHQ1-3', and 5'-HEX-nnnnnn-BHQ2-3'. I need to run it on the MIC RT PCR machine by Biomolecular...

28 July 2024 5,658 0 View

Can anyone help me with in providing the procedure for purification of GSTtagged protein by gst affinity chromatography without an automated machine?

Purification of gst tagged protein

25 July 2024 1,720 0 View

Does anyone know if there is a lab scale encapsulation machine available for purchase?

05 July 2024 3,888 1 View

How to carry out survival analysis of a one time use machine which is stored and tested at regular intervals for functionality?

I want to carry out reliability study of a machine with various sub components both electrical and mechanical. The machine is a one time use (similar to a decoy or rocket) and is stored at...

30 June 2024 2,435 0 View

How to cut a sample with several micrometers thick silicon oxide with DISCO DAD323 dicing machine?

I use a DISCO DAD323 dicing machine to cut my sample,which has 1-2 micrometers SIO2 on its top.However,the SIO2 is broken and fall apart everytime.I tried different cutting speed but didn't work....

20 June 2024 1,131 0 View

High Pressure on ÄKTA Start without column?

Hi everyone, I really don't know how to fix the issue that I am facing. For background, I am working on the purification of inclusion bodies protein, which require the use of 8 M urea in the...

09 June 2024 9,522 0 View

What are the modern types of dusting machine?

Dusting machine

09 June 2024 7,501 0 View

The dimensions of Fisherbrand 96 well plates?

I want to use Fisherbrand 96 well plate for my plate reader, but the machine does not have fisherbrand, so I have to find it manuallly. Also the plate is clear but in the machine we have costar...

30 May 2024 2,779 0 View

What are the advantages of organic fertilization machines?

organic fertilization machines

16 May 2024 1,376 1 View