The procedure compute?

02 March 2021 5,204 3 View

[Measurement invariance] - Do you test it on the full SEM model, on each construct separately, or both?

Hi everyone, I would like to know whether both cultural groups interpreted my questionnaire in a similar way. To do so, I conducted a measurement invariance analysis on the whole model of latent...

14 January 2021 1,845 3 View

Is it possible to do a closed loop control of a sine wave?

An analogue voltage sine wave signal is send from a PLC to a Piezo actuator. This actuator converts the voltage to force. A load cell checks what the applied force is and sends a mA-signal...

27 December 2020 7,037 3 View

[SEM] Why RStudio and AMOS report different p-values (but same estimates)?

Hi everyone, I have conducted a SEM analysis in AMOS then replicated it in RStudio. While I obtained identical estimates and model fit statistics, the p-values differ between software programs...

25 December 2020 3,669 4 View

What should my boundary conditions be in abaqus and how do I apply a sine load?

I want to model a T bone specimen that is subjected to a sine load. The specimen is clamped in as showed on the figure. I was wondering what I should chose as boundary conditions and how I can...

08 November 2020 9,766 4 View

Does anyone know instruments to measure "mental health literacy" in teachers?

Hi there, I am looking for questionnaires measuring mental health literacy in teachers and educators. does anyone know any studies in this area?

16 September 2020 1,682 4 View

Is there any possibility to get the estimated values (listed for every participant) of a specific latent variable in R or Mplus?

Is there any possibility to get the estimated values (listed for every participant) of a specific latent variable in R or Mplus?

17 June 2020 3,819 3 View

Literature for multilevel MCMC models?

Hey there, I am looking for literature or tutorial videos, which are concerned with the question of how multilevel markov chain monte carlo models are conducted in R or Mplus. Can someone help...

20 April 2020 7,801 1 View

How to generate a ROC-Curve for multilevel regression models?

Dear colleagues, Does anyone know, how to build a ROC-Curve and a AUC-Value concerning multilevel logistic regression models using R or Mplus. I would be very grateful for any articles,...

26 February 2020 8,930 3 View

P-values for Odds Ratio in R or Mplus?

Dear collegues, Does anyone know, how I can generate a p-value for an Odds Ratio using R or Mplus concerning a multilevel (multiple/simple) logistic regression model? Thank you very much in...

26 February 2020 3,771 4 View

Logistical regression using SPSS for a dichotomous dependent variable, with an independent variable of 1, 2, 5 and 10 seconds?

I have an experiment with 28 participants The independent variable is the times 1, 2, 5, and 10 used as the cross hairs during a task These 4 times were tested using 4 different blocks, each...

03 March 2021 9,692 2 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Can anyone provide the Support vector regression code structure of LIBSVM MATLAB or python ?

Please, if Gaussian Parameter optimization is possible in this code structure

28 February 2021 278 3 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

VIF very high, but correlation is low and coefficient is significant. Which one whould I choose?

Hello. I have a question whether if my coefficients (statistically significant) would be valid when VIFs are really high. In my model, there are independent variables(IV), moderating variables...

26 February 2021 956 13 View