Could anyone figure out what are these black elongated rod like particles in flowcam image?

The protein sample was analyzed after dropping. The buffer had NaCl in it. I just know that something that looks black might be air bubbles. But here these particles are elongated. So I couldn't...

07 December 2020 5,097 2 View

Can an associate editor become in charge of a submitted manuscript where 1/4 of the total references were associated with his/her own??

Is it appropriate to have Person A as an Associate Editor of a submitted manuscript - where 1/4 of the total references are his/her own and who has been a co-author with the corresponding author...

14 December 2019 7,092 3 View

Why I am getting 4 Bands on gel for single plasmid extraction ?

29 August 2016 204 5 View

Can anyone suggest the applications of ferromagnetic powdered mixed metal oxides in daily life?

I have prepared micron sized ferromagnetic powdered material and I am finding applications related to this material.

15 October 2013 556 2 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Is CD44 degraded in lysosome together with hyaluronan after CD44 mediated endocytosis of hyaluronic acid?

Also when RHAMM binds hyaluronic acid, they get internalized, will RHAMM also be degraded? Or both CD44 and RHAMM will be transferred back to the cell membrane? Asking for breast cancer cell line...

01 March 2021 8,169 2 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View