Which fluorescent dye to use for measuring total ROS production?

Is DCFDA appropriate for measuring total ROS production, or can it only detect certain types of ROS? If I want to measure total ROS production, which dye should I use?

01 March 2021 9,447 3 View

Why am i not getting solid after reacting APTES with salicylaldehyde?

The reaction of APTES with salicylaldehyde in ethanol leads to the formation of imine compound yellow solid which is mention in literature, but I am not getting yellow solid I don't know why? when...

28 February 2021 2,955 2 View

Distortion problem in Abaqus explicit?

Dear all. I'm modeling the RC column with cyclic displacement by Abaqus-Explicit. The concrete model used Concrete Plastic Damage model. However I'm facing with a error about the excessive...

01 February 2021 7,726 1 View

How can I remove bubble in WPU film?

I am trying to prepare water-based polyurethane films. When dried air bubbles were formed and destroys the film homogeneity, then I can't use this for mechanical test because of defects. Is there...

26 January 2021 701 1 View

Which one I should choose in Abaqus ?

Hello, plese give me your idea! I simulate one slab concrete affected by temperature at top and bottom surfaces. after that, have a static load distribution with small area put on top surface. I...

12 January 2021 5,769 4 View

Analysis and implementation of Kalman filter in fixed-point arithmetic?

I would like to implement a Kalman filter for tracking applications for IoT nodes. I cannot do floating point on our nodes but only fixed point. Could you recommend some good references?

23 December 2020 4,813 3 View

How to deal with negative factor loadings while performing PCA-MLR to calculate quantitative source contribution in air pollution studies ?

If I am getting some negative values in factor loadings while performing principal component analysis (PCA), then I should use that negative values to calculate daily source contribution using...

22 December 2020 5,248 1 View

What are the source markers of Naphthalene, Acenaphthylene and Acenaphthene in ambient atmosphere ?

Is any article available which reports the sources of these PAHs ?

22 December 2020 8,738 1 View

How to intepret data with significant ANOVA but not significant Tukey test?

I have this set of data: Treatment 1: 30.5; 34.5; 24.4 Treatment 2: 24.8; 20.8; 16.8 Treatment 3: 19.1; 21.4; 21.0 Treatment 4: 22.3; 26.1; 27.1...

25 November 2020 920 4 View

Acesulfame Potassium and Acesulfame and Conversion?

Dear to whom it may concern, Based on ChemAxon, I calculated pKa values of Acesulfame as follows: 1. pKa (Strongest Acidic): 3.02 2. pKa (Strongest Basic): -6 Because I would like to convert...

25 November 2020 4,577 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View