Does anyone knows about a comercial software to record pressure and temperature during reaction in an Autoclave?

Dear all: Currently I am working with polymerization reaction in a reactor. For this, I need to control temperature, pressure, agitation speed etc. For calculation of rate of polymerization, I...

07 February 2021 355 2 View

How to obtain the plot of frequency shift w.r.t. pressure in a micro resonator (cc beam) based MEMS pressure sensor in COMSOL?

I need to know how to plot the impact of pressure (0 - 100 kPa) (which is applied on the back side of diaphragm) on the frequency shift caused in the cc beam supported on the diaphragm with...

01 February 2021 5,805 17 View

Which one I should choose in Abaqus ?

Hello, plese give me your idea! I simulate one slab concrete affected by temperature at top and bottom surfaces. after that, have a static load distribution with small area put on top surface. I...

12 January 2021 5,769 4 View

What is the simplest way to implement data encryption for Arduino project that communicate through Bluetooth ?

I have developed a project based on Arduino that communicates through Bluetooth with Android application, I want to enhance its privacy through encryption so that data should be prevented up to...

07 January 2021 7,933 5 View

How to configure wifi password and SSID on NodeMCU ESP8266 through wifi direct instead on hardcoded credentials?

While working on IoT projects I mostly use NodeMCU ESP8266 firmware for IoT Implementation. For coding, I use Arduino IDE in which for connectivity with wifi router we define hardcoded variable...

07 January 2021 6,688 3 View

What's the reasonable loading control of nuclear protein in acute injury?

What's the reasonable loading control of nuclear protein in acute injury? Is HDAC1 or Histone H3 a resonable loading control of nuclear protein in acute injury model? How to explain total my total...

06 January 2021 1,607 2 View

The Joule-Thomson effect?

Hello I recently am suffering calculation of temperature change resulted from the Joule-Thomson effect when propylene gas at 35 oC at 2 bar passes through a membrane to vacuum pressure (~ 0 bar)...

23 December 2020 4,091 2 View

Analysis and implementation of Kalman filter in fixed-point arithmetic?

I would like to implement a Kalman filter for tracking applications for IoT nodes. I cannot do floating point on our nodes but only fixed point. Could you recommend some good references?

23 December 2020 4,813 3 View

Can anyone tell me the name of these parasites which I got from a marine fish?

I got these parasites from eye and intestine of a marine fish. Thank you.

09 December 2020 7,752 2 View

When available, are you planning to receive SARS-CoV-2/COVID-19 immunization? What do you most fear about it?

If possible, let us know about the which vaccine would be available in your geographic location.

06 December 2020 3,527 23 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

How to Eliminate cosine error and abbe error in LASER measurement system(for example Rhenishaw XL80)?

I like to do project in laser measurement system. My objective is to eliminate or reduce the cosine error, abbe error in Laser measurement system. I have Rhenishaw XL80 system. Please tell the...

28 February 2021 4,890 3 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

Can random sampling have inclusion criteria?

As random sampling means that everyone in the population have an equal chance to be chosen, can it have inclusion criteria? My research participants have been chosen based on the inclusion...

26 February 2021 6,905 10 View