I need to make patterns on RT duroid (5880) with trance and line widths of 20 micron. Copper clad thickness is 9 micron. Suggest some PCB fabrication companies who can handle this.
May be you can try in Ascent circuits near Hosur, road,Bangalore.Though I am not sure whether they take orders from Individuals. You can contact them.
Ascent Circuits Pvt. Ltd.,
Plot No. 111,
Sipcot Industrial Complex,
Phase 1, Hosur - 635126
Tamil Nadu, India
Ph : +91 04344 - 271123 / 271124
Fax : +91 04344 - 271148
E-mail : [email protected]
[email protected]
I have prepared a Erbium Doped Borate glass and I am working on calculations of Elastic Moduli of the glass. I have referred some of the articles but I couldn't understand how they have...
23 May 2024 5,707 0 View
I'm working on a project related to Luminescence Properties of Rare Earth Glasses (not Europium). I have read some articles related to Judd Ofelt Parameters, but I couldn't able to understand the...
26 March 2024 2,287 0 View
I have been trying to synthesize high methacrylation GELMA using the following protocol : Precise Tuning of Facile One-Pot Gelatin Methacryloyl (GelMA... However, I find that my GELMA is very...
24 March 2024 1,070 2 View
Hi, I synthesized GelMA using carbonate buffer and maintained the pH at 9 throughout the synthesis. The carbonate buffer was made with MilliQ water. Subsequently dialysis was done using MilliQ...
28 January 2024 2,011 0 View
I have conducted an experiment on the UV Absorption Spectrum for my glass samples and I have obtained the Absorbance values for the corresponding wavelengths. Unfortunately, I did not measure the...
17 December 2023 5,071 3 View
the fcc metal are not undergoing DBTT but bcc & hcp will undergoing and how it is happening
10 September 2023 6,550 0 View
explain theory and formula for calculating oxygen level in solid ingot. During pouring of liquid metal into ingot mold, after solidification, forging and heat treatment operation to know oxygen...
06 September 2023 248 0 View
why delta glaze is applying to titanium ingot before starting an forging operation
06 September 2023 8,716 0 View
what is the formula is used for creating a anti flacking cycle
20 August 2023 2,117 1 View
according to A606 code specified that to carry out low cycle fatigue test machine capacity should minimum 45kn-100kn. why load capacity of machine is specified.
20 August 2023 7,156 1 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...
28 July 2024 8,027 3 View
For example, if low-density polyethylene (LDPE) is equilibrated with PCB contaminated marine and freshwater sediments, can LDPE-lipid partition coefficients be used to obtain equilibrium...
28 July 2024 263 1 View
// interested in the difference between floating events and short circuits.
22 July 2024 6,565 0 View
Deep etching Negative photoresist Acrylate polymer Chemical etching Ferric chloride Crosslinking Resolution
11 July 2024 2,476 4 View
Hello, I am an Etch Engineer. I am performing etching with high T_ox/Nit selectivity using remote plasma. Etching plasma is formed using only NH3/NF3/H2. 1. I wonder if it would be advantageous...
11 July 2024 8,115 2 View
Dear Members, We are conducting a research survey on the Printed Circuit Board (PCBs) industry and would greatly appreciate your valuable input. To participate, click the following...
09 July 2024 4,936 1 View
I am creating a single element model in Abaqus of a composite material. My goal is to match the stress-strain curve of the material which was obtained experimentally. I am using VUMAT for Fabric...
07 July 2024 10,036 5 View
If I dope silver during the synthesis of copper indium sulphide nanoparticles by hydrothermal method what will be the size of nanoparticles?
13 June 2024 6,844 3 View
I am currently struggling to achieve a good surface finish on mounted Zn-2 samples. Both grinding and polishing (with SiC, silica and diamond) resulted in embedding of the grinding/polishing media...
11 June 2024 2,055 0 View