I have prepared a Erbium Doped Borate glass and I am working on calculations of Elastic Moduli of the glass. I have referred some of the articles but I couldn't understand how they have calculated. Kindly help me in this regard.
I need to calculate the conductivity of the my material. From the previous reported articles i got these formulas 1. σ ∝ exp(-Eg/2*Kb*T) Kb - Boltzmann constant T - Temperature (in kelvin) Eg...
25 April 2024 1,421 3 View
I'm working on a project related to Luminescence Properties of Rare Earth Glasses (not Europium). I have read some articles related to Judd Ofelt Parameters, but I couldn't able to understand the...
26 March 2024 2,287 0 View
I have been trying to synthesize high methacrylation GELMA using the following protocol : Precise Tuning of Facile One-Pot Gelatin Methacryloyl (GelMA... However, I find that my GELMA is very...
24 March 2024 1,070 2 View
Hi, I synthesized GelMA using carbonate buffer and maintained the pH at 9 throughout the synthesis. The carbonate buffer was made with MilliQ water. Subsequently dialysis was done using MilliQ...
28 January 2024 2,011 0 View
I have conducted an experiment on the UV Absorption Spectrum for my glass samples and I have obtained the Absorbance values for the corresponding wavelengths. Unfortunately, I did not measure the...
17 December 2023 5,071 3 View
I need to substitute N position with ethyl or methyl groups. How can I achieve this with good yield?
25 September 2023 7,446 1 View
the fcc metal are not undergoing DBTT but bcc & hcp will undergoing and how it is happening
10 September 2023 6,550 0 View
explain theory and formula for calculating oxygen level in solid ingot. During pouring of liquid metal into ingot mold, after solidification, forging and heat treatment operation to know oxygen...
06 September 2023 248 0 View
why delta glaze is applying to titanium ingot before starting an forging operation
06 September 2023 8,716 0 View
what is the formula is used for creating a anti flacking cycle
20 August 2023 2,117 1 View
I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?
08 August 2024 8,915 0 View
I will polymerise Aniline on ITO glass WE, using 1M of H2SO4 and a potentiostat. However, I am not sure if I have to do the electrochemical polymerisation inside a hood. Is it necessary? Is the...
10 July 2024 2,937 3 View
Hi all, I am looking glass cilinders that have an open flat bottom and top. Preferably with the inner diameter in the range of 2 cm. It's similar to the ones found on multi-electrode arrays for...
06 July 2024 5,846 1 View
If we want to introduce a material similar to polymethyl methacrylate "with the characteristics mentioned in the next paragraph" that can be added to a precursor and create a composite, which...
03 July 2024 2,371 1 View
I use PDMS to build a microfluidic system, but it is not hardening at all, although I use TEOS as a cross-linker and also ATPES in a ratio of 1:10, and it's been 3 days at 80 degrees of 3 ml cast...
01 July 2024 604 3 View
Is direct contact of polllutant and catalyst needed? or indirect contact just like photocatalyst wrapped inside glass can also create hydroxyl radicals and elimnate pollutants near to its wrapped...
23 June 2024 3,249 5 View
who retails few mm diameter polished circular glass plates ? thickness 0.1 to 1 mm diameter 1 to 3 mm ordinary or fused silica glass polished on both sides and the edge
16 June 2024 763 1 View
What share is made of steel? Plastics and glass? Aluminum? Iron?
15 June 2024 7,246 2 View
I used a two-phase extraction protocol (essentially the Bligh-Dyer or Folch protocol) to fractionate C. elegans into aqueous metabolites, lipids, and protein. These worms have been fed bacteria...
11 June 2024 8,991 1 View
We are currently trying to replace acetate when dehyrdating ("drying") cryo sections on glass slides with a less harmful alternative. For many chemical purposes ethyle lactate is recommended - has...
10 June 2024 5,213 3 View