What is delta glaze?

Jayaprakash Polamarasetty @Jayaprakash-Polamarasetty

07 September 2023 0 9K Report

why delta glaze is applying to titanium ingot before starting an forging operation

Badges
Science topic

More Jayaprakash Polamarasetty's questions See All

How to calculate the dissociation energy of the oxides per unit volume?

I have prepared a Erbium Doped Borate glass and I am working on calculations of Elastic Moduli of the glass. I have referred some of the articles but I couldn't understand how they have...

23 May 2024 5,707 0 View

Can someone explain the procedure for Calculating Judd Ofelt Parameters?

I'm working on a project related to Luminescence Properties of Rare Earth Glasses (not Europium). I have read some articles related to Judd Ofelt Parameters, but I couldn't able to understand the...

26 March 2024 2,287 0 View

Why is my GELMA opaque?

I have been trying to synthesize high methacrylation GELMA using the following protocol : Precise Tuning of Facile One-Pot Gelatin Methacryloyl (GelMA... However, I find that my GELMA is very...

24 March 2024 1,070 2 View

Why is my GELMA hydrogel degrading in two days ?

Hi, I synthesized GelMA using carbonate buffer and maintained the pH at 9 throughout the synthesis. The carbonate buffer was made with MilliQ water. Subsequently dialysis was done using MilliQ...

28 January 2024 2,011 0 View

How can one calculate the refractive index from the absorbance data of the glass?

I have conducted an experiment on the UV Absorption Spectrum for my glass samples and I have obtained the Absorbance values for the corresponding wavelengths. Unfortunately, I did not measure the...

17 December 2023 5,071 3 View

Why fcc metal will not undergoes ductile to brittle transition temperature?

the fcc metal are not undergoing DBTT but bcc & hcp will undergoing and how it is happening

10 September 2023 6,550 0 View

How to find oxygen level(ppm) of solid ingot?

explain theory and formula for calculating oxygen level in solid ingot. During pouring of liquid metal into ingot mold, after solidification, forging and heat treatment operation to know oxygen...

06 September 2023 248 0 View

How anti-flacking cycle is created in heat treatment?

what is the formula is used for creating a anti flacking cycle

20 August 2023 2,117 1 View

What is relationship between ultimate test vs load capacity of lcf test machine?

according to A606 code specified that to carry out low cycle fatigue test machine capacity should minimum 45kn-100kn. why load capacity of machine is specified.

20 August 2023 7,156 1 View

What is use of extensometer in lcf test?

the purpose of extensometer in low cycle fatigue test

20 August 2023 5,242 1 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

Does the delta function actually make sense to use on point particles?

The delta function seems produce logical contradictions when analyzed on a fundamental level. I would be curious if anyone else agrees.

31 July 2024 10,109 3 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

Convergence criteria not met but ends with normal termination. Could not open the log file in gaussview. How to rectify this problem?

>>>>>>>>>> Convergence criterion not met. SCF Done: E(RB3LYP) = -472.437545326 A.U. after 33 cycles NFock= 32 Conv=0.29D-07 -V/T= 2.2914...

16 July 2024 8,862 2 View

How does that stream's gradient change downstream as it enter the alluvial fan and difference between an alluvial plain and a delta plain?

12 July 2024 7,337 0 View

Could Nd doping into TiO2(anatse) because Nd's dense diameters are bigger than in TiO2 ?

could Nd (Neodimyum) doping into TiO2 because Nd's dense diameters are bigger than in TiO2

11 July 2024 2,350 2 View

Determine pore diameter by BJH of TiO2?

Dear all, l need to help me to determine pore diameter. I got from BJH data the rp(peak area), Desorption Isotherm was 1.6 nm, but from Isotherm l got type lV with hysteresis H2 loop. Can l used...

10 July 2024 2,872 1 View

What is the fastest method should i use to determine TiO2 content for thermoplastic without using any high tech instrument?

I currently conduct a hotmelt thermoplastic. I want to find the tio2 content in the product. As far as I know, titration method can be used since it is available for me. May I know what is the...

07 July 2024 5,264 3 View