Internal Combustion Engine- How to tell ANSYS which body is the Port and which are the Valves?

12 April 2021 0 10K Report

Hello there

I'm having an issue in DesignModeler when using Input Manager

I modeled the Intake and Exhaust Port and Cylinder as 1 body and 2 bodies for the valves using SolidWorks, saved it as .STEP and imported to DM.

The next step is to assign faces and bodies in Input Manager. This is when i noticed that DM is reading the exhaust valve as the Port, and the port as a Valve. The intake valve seems to have no issue.

I need to fix the geometry to complete the whole simulation with the proper zones and boundary conditions.

Badges
Science topic

More Ralph Semaan's questions See All

I'm trying to respond to a request for a reprint. It gives me a message in a red box --"An error occurred." Nothing more. Why?

I have the file, and prefer to send it privately (because I'm not a lawyer, and don't really know what permissions I have to send or post it publicly). Please advise if possible.

30 May 2024 3,622 3 View

How much glucose to add to LB media to prevent leaky expression?

I am already using BL21(DE3)pLysS cells but I am still getting leaky expression in pre-expression samples before IPTG is added. LB broth is tryptone, salt and yeast. Thanks :)

28 May 2024 2,820 2 View

MCherry tag being photobleached during expression?

I am expressing an mCherry tagged protein. Yield of total protein is good but the fluorescence intensity is very low (ie. Protein assays and gels show a lot of protein but this does not correspond...

28 May 2024 4,828 1 View

Probe-based qPCR not reaching plateau phase?

Hi, I'm in the process of developing a hydrolysis probe qPCR assay to quantify gene copy numbers of Microcystis 16S rDNA. In troubleshooting my cycling parameters, I'm getting resulting plots such...

15 January 2024 6,957 1 View

Nucleofection problem. What is the best buffer and the best program for nucleoporation?

I have been trying to transfect primary cells, essentially NK (CD56+) and monocytes (CD14+) using PiggyBac transposon system with no success. All cells die. I want to try some optimized protocols,...

31 October 2023 1,894 0 View

Any suggestions for extraction method for stem barks of Entada phaseoloides? and what rotational speed, time, and temperature for rotary evaporation?

There are limited research about Entada phaseoloides L. which is hard to know whether what extraction process of its stem bark. I saw few studies but they are reviews or an article

26 September 2023 3,071 0 View

What are some ways to repair cavities in stator coils?

During visual inspection, a cavity was detected in the stator coil of a hydroelectric stator. What are some proposed methods to repair this defect?

10 September 2023 5,709 1 View

Can i use Rehabilitation theory for my research topic entitled "Assessing the level of recreation program of detainees in jail" ?

Also, I have prepared other theories that can be likely used for the study, such as positive psychology theory to be used in the field of the criminal justice system. also I'm in need to help me...

09 September 2023 8,220 4 View

the expression of inflammatory genes and the secretion of inflammatory cytokines are not always correlated ?

Hello, I stimulate Cows PBMC with LPS and with an anti-inflammatory (6 hrs before the LPS) and another case (6 hrs after the LPS) Incubation time 24 hrs Results : RT Pcr decrease in the...

22 August 2023 1,956 0 View

Looking for Local and International Validators?

Good day, Everyone! I'm a second-year college student at De La Salle Araneta College, and we're seeking for both a local (Philippines) and an international validator for our thesis. The validator...

16 June 2023 8,197 6 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Regarding LBM in Boiling?

What should be the equation for halfway bounce back boundary condition for flow field with forcing term?

08 August 2024 7,938 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Element deletion problem in ABAQUS/Explicit solver using Cohesive elements?

I had a problem for so long. I could easily delete elements in ABAQUS implicit solver but I needed to use VUMAT so I had to have Explicit solution but the element did not disappear for so long. I...

23 July 2024 10,032 0 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View