In an unassigned interface zone, what is the meaning of src and trg in interface mesh of ansys meshing?

04 April 2015 1 3K Report

Dear colleagues

I have changed my mesh in a case and Unassigned interface zone error impedes my work.

In interface mesh panel, I see some src and trg inteface which is created in ansys meshing.

what does they mean(source and target)?

I should select to adjacent interface as a interface but I am afraid that is it different to select src/trg or trg/src?(in other words does they have any arrangment)

regards

Zol Bahri Razali

You can get the similar or apropriate answer by searching the keyword in the GOOGLE SCHOLAR page. Usually you will get the first paper similar to your keyword.

From my experience, this way will help you a lot. If you still have a problem, do not hasitate to let me know.

Kind regards, Dr ZOL BAHRI - Universiti Malaysia Perlis, MALAYSIA

BNT-BKT-BT. Available from: https://www.researchgate.net/post/BNT-BKT-BT#view=54f68badd3df3ee77c8b4638 [accessed May 7, 2015].

Badges
Science topic

More Mahdi Izadi's questions See All

What is a criterion for assuming a fluid as a well-mixed one?

Dear colleague as you know well mixedness is crucial assumption in CSTR reactors. which hydrodynamic parameter can be used for judging whether a liquid flow is well mixed, in fact I am trying to...

07 August 2015 9,803 4 View

Why do I detect stationary wall motion relative to adjacent cell zone?

Dear colleagues, for simulating a rotating impeller I have used MRF approach, Although I have changed all the walls to moving wall relative to adjacent cells with with zero velocity and same...

06 July 2015 7,859 10 View

Any advice on implementing a network of cell grid into fluent?

Dear colleagues I have used a fine mesh for simulating hydrodynamic of a case due to its high gradients but my heat transfer network can be coarser for lowering computation cost. for this goal I...

05 June 2015 8,831 1 View

Abnormal Concenteration prediction in fluent in heterogeneous reaction?

Dear colleagues I am trying to simulate a multiphase heterogeneous reaction in fluent. in this reaction there is a mixture of gas above a liquid pool. at first gas mixture is pure A and in...

03 April 2015 2,609 5 View

Error in interpolating data and mesh replacement in fluent?

Dear Friends I am trying to use a new mesh in a case and use last data and continue my run. All hydrodynamic variables (velocity,K,eps ,P) will be done but mass fractions couldn't be...

01 February 2015 2,343 4 View

What is the predicted flow time for convergence after adding reaction equation to a converged hydrodynamic case in fluent?

Dear colleagues. the hydrodynamic of a system has converged via fluent in a flow time tantamount to a minute.I want to add reaction equations to system and having hydrodynamic as a initial guess...

01 February 2015 6,749 5 View

Can anyone help me with scalability problem in parallelfluent on cluster?

I have ran fluent 14.5 on a cluster including 8 system with diferent number of cores and CPU frequencies (a 24 core with 3.67Ghz, a 16 core with 2.2 GHz, and 6 core with 2 Ghz)when I read data up...

01 February 2015 6,494 4 View

What is the cause of slow data reading in core mode in fluent parallel mode on cluster?

Dear Colleagues; I am doing a fluent parallel job on a 7 node 80 core heterogeneous system with different core number and size and different RAM also. When I schedule works by cores, my data...

31 December 2014 7,419 3 View

How do I use all cores in an Ansys fluent with their best efficiently?

for fluent 14.5; in a cluster of 7 different nodes I have used job schedule.cores have a gamut of 10 up to 90 percent activity. How should I use fluent efficiently? which one causes this defect?...

31 December 2014 4,014 1 View

Why do I have acute speed drop while reading FLuent case and data?

I have encountered an odd problem. I am trying to run parallel Fluent on a cluster include 7 nodes and 80 cores. I am using a Gigabit Switch and cat6 cables. While I am trying to read case and...

11 December 2014 8,901 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,047 2 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,664 0 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,031 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 355 3 View

Element deletion problem in ABAQUS/Explicit solver using Cohesive elements?

I had a problem for so long. I could easily delete elements in ABAQUS implicit solver but I needed to use VUMAT so I had to have Explicit solution but the element did not disappear for so long. I...

23 July 2024 10,032 0 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,893 1 View

The value of RF3(Z) in Abaqus model is huge how to control that?

I am modelling CFS Sheath wall in abaqus and i am applying the 100 mm displacement but i am getting high reach force close to 150 kN but i need it till 50kN. I have used mesh independent fastner...

27 June 2024 4,212 2 View

How to solve this error while I simulate gidl using tcad ?

There is an error message "interface silicon/oxide not found in grid xxx.tdr file"

26 June 2024 5,551 0 View