Dear colleague
as you know well mixedness is crucial assumption in CSTR reactors.
which hydrodynamic parameter can be used for judging whether a liquid flow is well mixed,
in fact I am trying to break a cfd domain to some cstr cases,
regards
1-For a homogenous reactor concentration is uniform through out the the medium.
2- For hetrogenous reactor the dispersion is uniform in the reactor.
3- In both cases take into account the dead points and retention time of the reactors.
4- check Books on mixer designs.
Hello,
You can calculate a mixing degree by CFD by injecting a Dirac of tracer in the CSTR inlet.. Then you may calculate ABS(1-c(x,y,z)/c_mean). All values in the reactor should be less than x% if you want a mixing efficiency of x%.
Regards
Eric
many many thanks!
virtual rtd seems to be a good way!
homogeneous distribution partial pressure
Dear colleagues, for simulating a rotating impeller I have used MRF approach, Although I have changed all the walls to moving wall relative to adjacent cells with with zero velocity and same...
06 July 2015 7,860 10 View
Dear colleagues I have used a fine mesh for simulating hydrodynamic of a case due to its high gradients but my heat transfer network can be coarser for lowering computation cost. for this goal I...
05 June 2015 8,831 1 View
Dear colleagues I have changed my mesh in a case and Unassigned interface zone error impedes my work. In interface mesh panel, I see some src and trg inteface which is created in ansys...
03 April 2015 2,811 1 View
Dear colleagues I am trying to simulate a multiphase heterogeneous reaction in fluent. in this reaction there is a mixture of gas above a liquid pool. at first gas mixture is pure A and in...
03 April 2015 2,610 5 View
Dear Friends I am trying to use a new mesh in a case and use last data and continue my run. All hydrodynamic variables (velocity,K,eps ,P) will be done but mass fractions couldn't be...
01 February 2015 2,343 4 View
I have ran fluent 14.5 on a cluster including 8 system with diferent number of cores and CPU frequencies (a 24 core with 3.67Ghz, a 16 core with 2.2 GHz, and 6 core with 2 Ghz)when I read data up...
01 February 2015 6,494 4 View
Dear colleagues. the hydrodynamic of a system has converged via fluent in a flow time tantamount to a minute.I want to add reaction equations to system and having hydrodynamic as a initial guess...
01 February 2015 6,750 5 View
Dear Colleagues; I am doing a fluent parallel job on a 7 node 80 core heterogeneous system with different core number and size and different RAM also. When I schedule works by cores, my data...
31 December 2014 7,419 3 View
for fluent 14.5; in a cluster of 7 different nodes I have used job schedule.cores have a gamut of 10 up to 90 percent activity. How should I use fluent efficiently? which one causes this defect?...
31 December 2014 4,014 1 View
I have encountered an odd problem. I am trying to run parallel Fluent on a cluster include 7 nodes and 80 cores. I am using a Gigabit Switch and cat6 cables. While I am trying to read case and...
11 December 2014 8,901 3 View
Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...
11 August 2024 8,140 3 View
Are there any suggestions or insights you can provide to help address this problem
06 August 2024 1,442 2 View
Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...
03 August 2024 3,371 3 View
I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?
02 August 2024 3,142 4 View
Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...
30 July 2024 433 3 View
Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...
29 July 2024 1,089 2 View
Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar
29 July 2024 3,083 8 View
If I want to calculate molecular dynamics (Gromacs), do I first need to optimize the geometry of the molecule? For example, I first draw the molecule in Avogadro, and then what? I guess I can't...
28 July 2024 672 3 View
AGILENT HPLC 1100 SERIES operation assistance needed.
25 July 2024 10,045 2 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,308 5 View