Is there a typical range in the power spectrum that each person has during a rest measurement? Moreover, are there differences between men and women?

Is there a typical range in the power spectrum that each person has in the individual brain areas (19 electrodes, 10-20 system) and frequency bands (theta, alpha, beta gamma) during a rest...

13 January 2021 5,660 3 View

Can I calculate the coherence of two EEG signals on a given frequency band or do I have to calculate them over the entire frequency range?

I would like to know whether I first have to calculate the coherence between two signals over the entire frequency spectrum in matlab and summarize the specific frequency bands from these values...

09 May 2019 9,695 2 View

Do companies have an ethical obligation to inform candidates they will be reviewing their social media accounts?

I discuss this topic in my class and want to write a paper on this subject. Given that 70% of employers view candidates' social media accounts, are companies obligated to disclose this to...

27 January 2019 3,604 8 View

How can I prevent bubbles from forming under a coverslip?

My colleague and I are having some trouble mounting 70 micrometer mouse brain slices. When we initially position the coverslip over the mounted slices, there are no bubbles but when we come back...

10 February 2021 3,580 1 View

How can I remove bubble in WPU film?

I am trying to prepare water-based polyurethane films. When dried air bubbles were formed and destroys the film homogeneity, then I can't use this for mechanical test because of defects. Is there...

26 January 2021 701 1 View

How can I get rid of the bubbles in the SBS membrane?

I used methylcyclohexane/ ethylcyclohexane / n-butyl acetate mixed solvent to dissolve thermoplastic SBS & terpene resin. The mixture is then poured onto a glass substrate. After solvent...

24 January 2021 8,306 3 View

Can anyone provide me a protocl of Native PAGE with the 30% terminal resolving gel concentraion?

I am separating the AuCNs, which are Au nanoclusters. I used the 3% stacking and 30% resolving polyacrylamide from the reference. Eachtime when the resolving gel is polymerizing, plenty of heat...

22 January 2021 8,522 3 View

Where can I find these two papers?

14 January 2021 1,572 3 View

How to model bubble coalescence and/or departure from a surface in ANSYS Fluent?

Dear all, I would like to simulate the pool boiling (subcooled). Specifically, I'm interested in departure of bubbles from finned surfaces. I want to do it in ANSYS-Fluent. Is it possible? if so,...

14 January 2021 6,304 5 View

Best way to get air out of a hamilton syringe?

I'm using a hamilton syringe to inject mineral oil through PVC tubing attached to the needle tip of the syringe. To make sure the tubing stays free of bubbles, I have to get all the air out of the...

10 January 2021 8,082 1 View

Why is PVDF splashing and bursting under vacuum ?

I prepared PVDF in a very regular way by dissolving it with stirring at room temperature but when i placed it in vacuum for eliminating the bubbles and trapped gases it started to burst and...

09 January 2021 3,965 3 View

Bubble column design?

A bubble column of 10 m height and 1m diameter (implying high hydrostatic pressure difference) is being fed leisurely with a flow rate of 10 L/min. What is the resulting dissolved oxygen profile...

31 December 2020 524 1 View

How to model bubble in Ansys Fluent?

I am seeking to model a simple bubble growth/collapse in Ansys. I have tried using 2D, VOF with an initial patch air circle geometry surrounded by water. I include surface tension and make the air...

10 December 2020 9,113 3 View