Samples do not run
Please be clear with with problem, not able to understand.
Is it that your gel has run half way only, if so pass voltage to allow it move to the other end.
Sounds more like there is problem with casting of your gel...
I ran two gels in one unit. One of them rum properly but other do not.. i used 100V voltage
I think there would be a problem in your casting or loading. Also check the wells for leakage.
Why dont you rerun the half run gel. I feel you have applied less voltage. We generally use 200V voltage for one small unit, and it takes it about 30min to run completely.
Thanks a lot to all. i will do it again. thanks.
Please help me finding sequence of the PR(Pathogen related) genes expressed during HR (hypersensitive response) in N.tabaccum, either acidic or basic. I need all. Thanks
07 August 2015 1,945 1 View
I have SALK sequence no of a T-DNA mutant of a gene. now i want to make a genomic diagram with the position of insertion. How could I find the position of insertion. I check the SALK homepage but...
05 June 2015 8,450 5 View
when we go to SALK site, page opens like CLON SAIL.... TYPE SALK T-DNA CHRO chr3 EVAL 0.0 COOR C/16757979-16758431 what is COOR stands for. is this for the position of insertion of T-DNA
05 June 2015 6,760 0 View
I isolated my plasmid (includes my insert) from GV3101 by mini prep kit but the concentration is too low. is there any other method to isolate the plasmid from GV3101?
04 May 2015 2,733 9 View
I extracted total protein from agro-infiltered N. benthamiana leaves by using following extraction buffer :- Protein Extraction Buffer- 50mM Tris/HCl pH 7.6, 100mM NaCl, 0.05% Tween20, 1mM EDTA,...
02 March 2015 5,794 6 View
I already extracted my protein directly in SDS buffer containing Bromophenol blue and also B-mercaptoethanol. After running SDS page, I am having problem with protein concentration. Is there any...
31 December 2014 6,750 12 View
Please some one suggest me a good protocol, giving high yield of ER membrane and nuclear protein (if both protein extraction in same buffer, then better) from agroinfilterated Nicotiana...
31 December 2014 329 4 View
SDS page troubleshooting.
10 November 2014 6,509 18 View
I know the sequence of my gene but want to do the RACE to confirm the position of 5 end prime and 3' end prime. Now, I am confused about how RACE works in this case and we can say by seeing at...
06 July 2014 8,533 3 View
I have two genes. I am isolating both of them (gel purification), then using each gene in one reaction of PCR with end primers for fusion of both genes, but each time I don't get any results for...
03 April 2014 2,714 26 View
Currently, when I run SDS-PAGE, I don't see any bands at all, even though I used the same material just a day ago and it worked fine.... In our lab, we dilute the 10X running buffer to 1X and...
06 August 2024 5,373 2 View
I have been working on Red blood cell-derived extracellular vesicles as Antisense Oligonucleotide (ASO) carriers. We normally run agarose gel to quantify the loading efficiency. I used naked ASO...
06 August 2024 3,130 2 View
I ran a SDS-page of a bacterial lysate and I want to quantify protein concentration in a specific band. I was thinking of using a standards ladder or make some standards are different...
05 August 2024 9,805 3 View
It's an end-point PCR protocol. I'm using 1.5% agarose gel with SyBR Safe dye and TBE as a running buffer, visualization on BioRad XR+ system. I was primarily thinking of primer efficiency,...
01 August 2024 4,673 4 View
I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...
29 July 2024 950 4 View
I am performing IgG purification and I have to show my results on SDS-PAGE. I use 10% tris glycine gel and prepare the samples under non reducing conditions. I am new to antibodies and therefore...
23 July 2024 6,664 6 View
Greetings. I’m currently running a nested pcr for giardia. My mastermix comprised of 3mM Mgcl2, 5unit of taq polymerase, 0.2uM of forward and reverse primers each respectively and 0.2mM of dNtp...
22 July 2024 9,761 5 View
I’m having difficulty achieving high RNA integrity in my samples. Although the 260/280 and 260/230 ratios are satisfactory after RNA extraction, the RNA samples show signs of degradation when...
22 July 2024 155 4 View
Hello, I was running a 12% SDS Page electrophoresis on few granulosa cell samples and got this result after the ponceau staining. The total protein lysate seem to aggregate at 70 kDa ladder mark...
21 July 2024 5,128 4 View
Sometimes I see the shadow like bands and its not true band. I want to know that what's the reason for it. I am using 2% gel for running genotyping samples I have uploaded the gel picture in both...
19 July 2024 148 6 View