Can anyone help or comment on solubilising chlorobutanol in aqueous injections in minimum time possible?

Please suggest solubilisation of chlorobutanol in injections. Tried pH and high temperature. But the issue is of assay drop. If anyone can suggest any solution. Its a commonly used excipient for...

21 February 2021 7,397 1 View

Solar energy production forecasting ?

Hello everyone! I am interested in the topic of solar energy production forecasting for a ground-mounted PV system of more than 100MW capacity. Can anyone please suggest what are the main data...

08 February 2021 6,834 5 View

Why AC cables are always covered with the sand first and then covered with soil in solar park ?

I was curious to know why we only use sand for covering the AC cables inside the trenches and instead of having good isolation why these cables are covered. Why is there a problem in the trenches...

13 January 2021 6,008 3 View

Error encountered in executing MCE ?

In Terrset, an error encountered in executing Spatial Decision Modeller (MCE). During execution or run the MCE a massage come on the screen that reflects "Your columns and rows are not same" , I...

07 December 2020 1,542 1 View

How to do extract Urban Heat Island separately from LANDSAT image for each land classes?

I have already been read many articles and found some methods but those are not cleared to me. Can you please suggest me how to generate different LST map of each land classes using ArcGIS? Or...

25 October 2020 5,978 5 View

Can someone advise me to do Rietveld Refinement of the material whose Crystallographic Information Framework (CIF) file is not available?

10 October 2020 7,411 9 View

Is generic vaccine after brand vaccine will meet up demand of covid 19 in near future?

is generic vaccine after brand vaccine will meet up demand of covid 19 in near future? what advance steps of management can be taken from end of December? Also we can get vaccine at low price if...

02 October 2020 4,651 1 View

When can we use Fisher's Least Significant Difference (LSD) test?

Hi, Following a two-way analysis of variance (ANOVA), when can we use Fisher's Least Significant Difference (LSD) test? Is it reliable or explainable showing data? I have some mouse behavior data...

28 September 2020 9,374 5 View

Recombination in Light emitting diode?

Why does recombination release light? It's one thing to say, 'and when the electron drops down it releases light', but it would be another level to explain how an electron dropping down creates...

28 July 2020 2,360 4 View

Systematic Review and Meta-analysis?

Hi, I am planning to conduct a systematic review and meta-analysis since very long. However, found difficulty in literature search and statistical analysis. Please anyone advice me any easy way...

11 July 2020 7,868 13 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View