I am modelling and analyzing the pipe bend in ABAQUS/CAE and element type is C3D20R.. How can i add uniform pressure in initial step?

More Manish Kumar's questions See All

How to apply internal pressure as traction boundary condition in ABAQUS?

How to apply surface traction boundary condition as internal pressure in pipe bend analysis in abaqus.

03 April 2019 8,603 1 View

How to extract moment-end-rotation data in two step abaqus pipe bend analysis?

In pipe bend analysis, I am carrying out two step analysis. In first step, internal pressure applied and in second step rotation is applied. Now, how to extract their moment-end-rotation data?...

02 March 2019 2,130 5 View

How to print float number in python using for loop?

How to print float number in python using for loop? i=0 j=0 for i in range (0,3,0.1): for j in range (0,4,0.1): print(i,j) TypeError: 'float' object cannot be interpreted as an integer

04 May 2018 5,711 4 View

Importing numpy package (latest package) to abaqus 2017?

How to import Numpy package (Python 3.6) to Abaqus 2017?

04 May 2018 1,366 0 View

How to form empirical equation for Collapse moment from FEA results?

I am working on Pipe bend analysis. I am having some FEA results for collapse moment. I need to form empirical formula. How to do that?

02 March 2018 6,154 4 View

How to get closed form solution from FEA results?

I am studying research papers relevant pipe bend/elbow analysis. In most of the papers closed form solution has been given. How this closed form solution are obtained I just didn't understood....

01 February 2018 9,780 3 View

How to get moment vs rotation curve for pipe bend analysis in Abaqus software?

I have done some analysis of pipe bend. To calculate the limit load Moment vs Rotation curve is must. Anybody please explain how to obtain it?

01 February 2018 5,758 2 View

I'm studying the pipe elbow but i don't know how to assign Elbow element . I am not able to find ELBOW elements. Can anyone suggest about it?

I'm studying the pipe elbow but i don't know how to assign Elbow element in ABAQUS/CAE. I am not able to find ELBOW elements. Can anyone suggest about it? i dont know where to find it in abaqus...

11 December 2017 2,462 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View