modelling, moving mesh
If you interest about the heat transfer from / to the rotating cylinder, please notice:
https://www.researchgate.net/publication/311278595_Investigation_of_Heat_Transfer_and_Fluid_Mechanics_across_a_Heated_Rotating_Circular_Cylinder_in_Crossflow
https://www.researchgate.net/publication/309335286_Investigation_of_Heat_Transfer_and_Fluid_Mechanics_across_a_Heated_Rotating_Circular_Cylinder_in_Crossflow?_iepl%5BviewId%5D=OzDEywmAYRaJQ3TrFqqHjoZ9&_iepl%5BprofilePublicationItemVariant%5D=default&_iepl%5Bcontexts%5D%5B0%5D=prfpi&_iepl%5BtargetEntityId%5D=PB%3A309335286&_iepl%5BinteractionType%5D=publicationTitle
https://www.researchgate.net/publication/311063828_Experimental_and_Numerical_Investigation_of_Heat_Transfer_and_Fluid_Mechanics_across_a_Rotating_Circular_Cylinder_Dissipating_Uniform_Heat_Flux_by_Crossflow?_iepl%5BviewId%5D=OzDEywmAYRaJQ3TrFqqHjoZ9&_iepl%5BprofilePublicationItemVariant%5D=default&_iepl%5Bcontexts%5D%5B0%5D=prfpi&_iepl%5BtargetEntityId%5D=PB%3A311063828&_iepl%5BinteractionType%5D=publicationTitle
If you interest about the cylinder with/ without heat transfer and focus on the hydrastatic chatraters please notice:
https://www.researchgate.net/publication/309152614_Experimental_and_theoretical_investigation_of_the_effect_of_rotating_circular_cylinder_speed_on_the_lift_and_drag_forces
Good luck
Conference Paper Investigation of Heat Transfer and Fluid Mechanics across a ...
Article Experimental and Numerical Investigation of Heat Transfer an...
Article Experimental and theoretical investigation of the effect of ...
Dear Srikanth Rangarajan:
You don't need to select the moving mesh. Just select the boundary of the cylinder as 'wall' and specify the wall as moving, then select 'rotating', then put the rotating wall in ' rad/sec'.
Please see the image attached. I am trying to simulate boiling of water flowing inside a channel using COMSOL. how do I get started
11 December 2017 949 1 View
can heat flux and convective heat loss modeled at the same surface in fluent?
10 November 2017 4,856 5 View
Phase change
02 March 2016 8,425 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...
29 July 2024 2,032 2 View
Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...
27 July 2024 356 3 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?
09 July 2024 9,226 3 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View
hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.
03 July 2024 5,418 4 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View