Does anyone know how to simulate boiling of flowing water inside a channel using COMSOL?

Srikanth Rangarajan @Srikanth_Rangarajan

12 December 2017 1 879 Report

Please see the image attached. I am trying to simulate boiling of water flowing inside a channel using COMSOL. how do I get started

Mohammad Zandsalimy

Hi,

Just have a look at the manual. I'm sure it helps a lot. Good luck.

https://www.comsol.com/models

cheers

Badges
Science topic

Similar topics
Computer Science
Images

More Srikanth Rangarajan's questions See All

I am trying to model the top layer of PV solar panel. I am interested in knowing how to specify both heat flux and heat loss at the same boundary?

can heat flux and convective heat loss modeled at the same surface in fluent?

10 November 2017 4,794 5 View

I am trying to simulate phase change(melting and solidification) using enthalpy-porosity in fluent. Any suggestions for better numerical model?

Phase change

02 March 2016 8,356 1 View

I am modelling a cylinder filled with air. I want to rotate the cylinder. Any idea how to do this in ansys fluent?

modelling, moving mesh

02 March 2016 7,753 3 View

Anyone plz suggest relevant topic for research in image processing+Deep learning.?

I have selected brain tumor images ...but now found that already lots of research done n this topic.

03 March 2021 5,774 3 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to find the mode of classified ocean colour images?

Hello, I have classified 10 S3 OLCI images from the same area (althouth not the same size and/or quadrant) and I would like to do a final image using the mode of the pixel of these 10 images. I...

01 March 2021 9,874 3 View