I need a tutorial to simulate the wear using Archard model for no. of working cycles. Thanks in advance.
I want to calculate the maximum Green-Lagrange strain in a elastomeric seal. How to calculate it in Abaqus? Is any field output available for the same? or do I require to right a code?
02 March 2017 3,242 4 View
Concentrated force, pressure etc?
10 November 2016 9,376 0 View
I am analyzing the elastomeric seal subjected to very high pressure. The stress generated is above the elastic limit. Which material model needs to be implemented to take the plasticity into...
02 March 2016 3,802 4 View
In a highly nonlinear FEA problem involving all the three nonlinearities, is it possible to carry out mesh convergence study? If the geometry is fairly simple but the problem is highly nonlinear...
31 December 2015 1,326 9 View
I need to model the macro and microscale contact mechanics phenomenon for a seal-rod interface. what is the difference between the two?
05 June 2015 7,535 5 View
I am modelling a seal/rod interface.I want to assemble the seal which is in initially compressed state.How to model such a problem.
05 June 2015 8,228 6 View
I have a pressure pulse curve for impact loading which I am applying with the amplitude option. I would like to apply it for 10000 cycles. How can I minimize the computation time for such case?
02 March 2015 7,042 5 View
turcite wear rings have been used to prevent metal to metal contact of cylinder bore and piston rod. How can one model turcite material, which is thermoplastic, in abaqus?
01 February 2015 5,227 4 View
I have the pressure pulse curve of the impact load. I want to apply it on a linear actuator system. How can this be done?
01 February 2015 6,595 1 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View