I am modelling a seal/rod interface.I want to assemble the seal which is in initially compressed state.How to model such a problem.
Hi,
You can use the interference fit option in Abaqus.
Thanks & Regards,
Ranjith.
1. www.ncaur.usda.gov/SP2UserFiles/Place/60100500/.../tekeste_06b.pdf
Hi Kul, try the above piece. Good luck
*Initial conditions, type = stress
hi,
the simplest way is using multi step analysis with pre-defined field stress as a initial condition.
Thanks everyone. my prob solved with the interference fit option
what is interference fit option in abacus?
I want to calculate the maximum Green-Lagrange strain in a elastomeric seal. How to calculate it in Abaqus? Is any field output available for the same? or do I require to right a code?
02 March 2017 3,242 4 View
Concentrated force, pressure etc?
10 November 2016 9,376 0 View
I need a tutorial to simulate the wear using Archard model for no. of working cycles. Thanks in advance.
05 June 2016 3,533 0 View
I am analyzing the elastomeric seal subjected to very high pressure. The stress generated is above the elastic limit. Which material model needs to be implemented to take the plasticity into...
02 March 2016 3,802 4 View
In a highly nonlinear FEA problem involving all the three nonlinearities, is it possible to carry out mesh convergence study? If the geometry is fairly simple but the problem is highly nonlinear...
31 December 2015 1,326 9 View
I need to model the macro and microscale contact mechanics phenomenon for a seal-rod interface. what is the difference between the two?
05 June 2015 7,535 5 View
I have a pressure pulse curve for impact loading which I am applying with the amplitude option. I would like to apply it for 10000 cycles. How can I minimize the computation time for such case?
02 March 2015 7,042 5 View
turcite wear rings have been used to prevent metal to metal contact of cylinder bore and piston rod. How can one model turcite material, which is thermoplastic, in abaqus?
01 February 2015 5,227 4 View
I have the pressure pulse curve of the impact load. I want to apply it on a linear actuator system. How can this be done?
01 February 2015 6,595 1 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 647 2 View
Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...
17 July 2024 1,501 1 View
I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...
16 July 2024 8,436 0 View
Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...
15 July 2024 3,491 0 View