How do I apply impact load in Abaqus?

02 February 2015 1 7K Report

I have the pressure pulse curve of the impact load. I want to apply it on a linear actuator system. How can this be done?

Kaustubh Kulkarni

Thanks...I will try it

Badges
Science topic

More Kaustubh Kulkarni's questions See All

How to calculate Green-Lagrange strain in a seal with hyperelastic properties in Abaqus?

I want to calculate the maximum Green-Lagrange strain in a elastomeric seal. How to calculate it in Abaqus? Is any field output available for the same? or do I require to right a code?

02 March 2017 3,242 4 View

Which type of loading is recommended for a nonlinear FEA?

Concentrated force, pressure etc?

10 November 2016 9,376 0 View

How to perform wear simulation in MSC Marc?

I need a tutorial to simulate the wear using Archard model for no. of working cycles. Thanks in advance.

05 June 2016 3,533 0 View

How to model rubber plasticity in abaqus?

I am analyzing the elastomeric seal subjected to very high pressure. The stress generated is above the elastic limit. Which material model needs to be implemented to take the plasticity into...

02 March 2016 3,802 4 View

Mesh convergence study in a highly nonlinear FEA problem?

In a highly nonlinear FEA problem involving all the three nonlinearities, is it possible to carry out mesh convergence study? If the geometry is fairly simple but the problem is highly nonlinear...

31 December 2015 1,326 9 View

What is the difference between macro and micro scale elastic contact?

I need to model the macro and microscale contact mechanics phenomenon for a seal-rod interface. what is the difference between the two?

05 June 2015 7,535 5 View

How can I give precompression in Abaqus?

I am modelling a seal/rod interface.I want to assemble the seal which is in initially compressed state.How to model such a problem.

05 June 2015 8,228 6 View

How can I apply repetitive impact load in Abaqus?

I have a pressure pulse curve for impact loading which I am applying with the amplitude option. I would like to apply it for 10000 cycles. How can I minimize the computation time for such case?

02 March 2015 7,042 5 View

How can one model turcite wear ring thermoplastic material in abaqus?

turcite wear rings have been used to prevent metal to metal contact of cylinder bore and piston rod. How can one model turcite material, which is thermoplastic, in abaqus?

01 February 2015 5,227 4 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View