How to open an external mesh file (in any software) so that we can analyse it? Mesh is a .msh file. Can anyone suggest any software for this?

04 April 2018 0 437 Report

I have been trying to read someone's mesh. I am not able to open it in fluent or hypermesh. Given file is in .msh format. We can add it in fluent directly but cannot open it in ansys meshing.

Can anyone suggest something, it will be a great help.

Badges
Science topic

More Anirudh Singh's questions See All

Can anyone answer the "Invalid cp problem at a particular temperature in fluent"? It will be a great help?

Invalid cp problem occurs in my fluent window. If I change cp of one material then same error occurs due to other. Is it a problem of mesh? Or any other problem. Please Help.

03 April 2019 5,357 4 View

What is the relation between the mass flow rate and flow area in DPM injections in Fluent? (Please see description) ?

I have been trying a lot to control the injection flows in the discrete phase model in fluent. But the on hand calculations are are far different from the numerical values provided in fluent. We...

02 March 2018 1,649 0 View

Is there a specific model for gasification in fluent or do we have to use a UDF ?

I have performed combustion quite a few times but I am unable to do gasification. Is there a particular model in fluent or do we have to use a UDF. Do we specify products in species transport or...

31 December 2017 8,696 5 View

What is the difference between species transport model and non premixed model in ansys fluent?

Non premixed is understood theoretically but practically (physically) I am unable to imagine what is species transport model.

10 November 2017 9,007 10 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View