What is the impact factor of Advances in OptoElectronics?

I would like to find the impact factor of the above journal. The ISSN is 1687-563X. Please help to ensure it. Since I could not through a google search. Thank You/

31 December 2018 8,107 5 View

How to fix MEMDDI and MWORDS allocations in MP2 calculations using GAMESS..?

I try to run a MP2 calculation and I end up with the following, Error ENOSPC: The number of shared memory identifiers for the node has been reached. I ran exetyp=check and I used those values...

02 March 2017 1,626 8 View

How to run conical intersection locating calculations using GAMESS..?

I would like to know the error of the attached input file to be run on GAMESS. Thank You,

09 October 2016 6,534 0 View

What is orthoganolity in tddft calculation..?

I want to know why TDDFT excitation calculations are orthogonal in electronic excitation calculations. Is it a disadvantages ...?

06 July 2016 7,030 2 View

What is the different between HF and RHF ...?

How to use HF and RHF depending on the application for energy minimization using quantum chemistry software. Thank You.

05 June 2016 6,537 2 View

How to fix Z-VECTOR FAILED TO CONVERGE in gamess

02 March 2016 7,806 0 View

How to interpret lambda diagnostic in gamess TDDFT calculation..?

I would like to know the relationship between oscillator strength and the lambda diagnostic since those two factors do not behave as the same for a possible excitation . Thank you.

02 March 2016 1,160 2 View

How to generate wfn file ...?

I want to calculate excitation electron population using gamess .I used AIMPAC key word I could not find .wfn file . Then I used tdprp as well now I have .dat file . Can I use that file to make a...

02 March 2016 9,662 10 View

How to calculate molecular volume ?

I would like to know how to calculate the volume of a molecule using Argus lab (preferred) or any other free ware.Please help with the descriptive steps. Thank You.

01 February 2016 5,492 2 View

How theoretical molecular excitation occurs ..?

I would like to know how theoretical excitation of a molecule occurs when we are using TDDFT.What sorts of conclusions can we gain through calculations..? I need to make explanation on it. Thank You.

31 December 2015 3,169 2 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

Is it possible for two human neuronal cell lines to have different gene sequence for the same protein?

I am looking at the ATP1A2 (Sodium/Potassium ATPase alpha subunit 2) in two human neuronal cell lines. Expression levels of this protein seems to be almost equal when detected by one antibody....

01 March 2021 3,607 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Is CD44 degraded in lysosome together with hyaluronan after CD44 mediated endocytosis of hyaluronic acid?

Also when RHAMM binds hyaluronic acid, they get internalized, will RHAMM also be degraded? Or both CD44 and RHAMM will be transferred back to the cell membrane? Asking for breast cancer cell line...

01 March 2021 8,169 2 View