How to import Creo sketch to ANSYS Design Modeler?

More Levente Kis's questions See All

Ansys explicit dynamics conpution time vs end time?

I cannot really understand, so I will need a little help. I have an explicit dynamic simulation. If I set the end time to 0,0001s it finishes in a few minutes, but if I set it to 1s (which is the...

24 April 2022 321 1 View

Does anybody has experience with MSC Marc/Mentat 2020FP1 under newer versions of SUSE than officially supported?

The current supported SUSE version for MSC Marc/Mentat 2020FP1 is SUSE 12SP1/SP2. However, the currently available SUSE version is SUSE Linux Enterprise 15 Service Pack 2. Does anybody has...

28 February 2021 3,468 0 View

What test is appropriate instead of McNemar-Bowker if the contingency table for related-samples categorical variable is not k x k?

I faced a problem with non-symmetric (non k x k) contingency tables in SPSS. I have categorical variables for a certain pathology (theoretically scored 0-3), and I want to compare the scores of...

01 January 1970 9,993 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

Is anyone aware of any Bronze Age or Neolithic pendants made of siltstone with serrated edges?

Excavation in 2007 in Northern Scotland along the East Coast revealed a domestic site containing the unbroken half (other half is missing) of a perforated circular disc measuring L 37mm x W...

27 July 2024 6,019 0 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

Panchanand Jha

Better go for APDL

Ajay Kumar Kakumani

If it is a 2D sketch, save as the sketch to DWG/ DXF and import the same into Space claim/ Design modeler of Ansys. If it is a 3D sketch save it as a Creo part and import the same in Space claim/ Design modeler.

Khaled Megahed

save it as a dwg/dxf from http://support.ptc.com/help/creo/creo_pma/usascii/index.html#page/data_exchange/interface/About_Exporting_Drawings_to_DXF_or_DWG_Files.html