Stress strain curve plot from ansys structural analysis is always linear?

I am trying to plot stress-strain curve for a simple solid block of 3*3*3 mm structural steel with load on top and bottom is constrained. Analyzing with step controls (20 substeps)with large...

04 May 2019 4,120 12 View

How to view the solution model for parameterization of design in ANSYS?

I am doing parametric analysis. Well i got the solution of all three parametrized values. How I can visualize for all the solutions. Visualization of model analysis is showing only first...

08 September 2018 3,200 4 View

How to fix rigid body in ansys workbench ?

I am evaluating deformation behavior of porous block of 10*10*10. For this i put this model between 2 plates. Stiffness behavior for plates I had given is rigid. Form the target node from top...

08 September 2018 4,254 5 View

Any suggestions on structured meshing of the swirler flow domain?

01 February 2018 2,340 1 View

Any list of publisher which gives free permission to reproduce material?

Does any one have list or information about the publishers who provides permission to reproduce copyrighted material without any charge.

31 December 2017 3,610 5 View

How to select adjacent offset nodes for irregular geometries in APDL?

Hey all ! I want to select offset nodes in ansys APDL from a irregular surface uniformly. I tried selection logic but failed because constructed surface is not in defined coordinates (PFA...

08 September 2016 8,878 3 View

*VWRITE command in ansys is not executing ?

02 March 2016 10,016 3 View

Does gpu acceleration in ansys needs hpc license?

I am planning to buy workstation with a budget of 7000 USD. What should be the right choice for which computation time should be reduced. As i had read from ansys forum and other that increasing...

06 July 2015 1,789 1 View

Is there any advice on modeling of porous structure in CAD packages ?

Is their any FE modeling software to create porous structure in any solid model. Basically I am designing acetabular cup in CREO on which i want to create trabecular porous structure on...

01 February 2015 5,193 10 View

Is there an option to change color of any point or portion of .PART in creo parametric?

In assembly mode, when we assemble two parts, while moving mouse on assembled parts it always highlights two pats, showing its lines and volumes.Such like is their any option or method to show...

31 December 2014 336 1 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View