Stress strain curve plot from ansys structural analysis is always linear?

I am trying to plot stress-strain curve for a simple solid block of 3*3*3 mm structural steel with load on top and bottom is constrained. Analyzing with step controls (20 substeps)with large...

04 May 2019 4,120 12 View

How to view the solution model for parameterization of design in ANSYS?

I am doing parametric analysis. Well i got the solution of all three parametrized values. How I can visualize for all the solutions. Visualization of model analysis is showing only first...

08 September 2018 3,200 4 View

How to fix rigid body in ansys workbench ?

I am evaluating deformation behavior of porous block of 10*10*10. For this i put this model between 2 plates. Stiffness behavior for plates I had given is rigid. Form the target node from top...

08 September 2018 4,254 5 View

Any suggestions on structured meshing of the swirler flow domain?

01 February 2018 2,340 1 View

How to select adjacent offset nodes for irregular geometries in APDL?

Hey all ! I want to select offset nodes in ansys APDL from a irregular surface uniformly. I tried selection logic but failed because constructed surface is not in defined coordinates (PFA...

08 September 2016 8,878 3 View

*VWRITE command in ansys is not executing ?

02 March 2016 10,016 3 View

How to give user defined colour of face in ANSYS DM ?

31 December 2015 6,319 4 View

Does gpu acceleration in ansys needs hpc license?

I am planning to buy workstation with a budget of 7000 USD. What should be the right choice for which computation time should be reduced. As i had read from ansys forum and other that increasing...

06 July 2015 1,789 1 View

Is there any advice on modeling of porous structure in CAD packages ?

Is their any FE modeling software to create porous structure in any solid model. Basically I am designing acetabular cup in CREO on which i want to create trabecular porous structure on...

01 February 2015 5,193 10 View

Is there an option to change color of any point or portion of .PART in creo parametric?

In assembly mode, when we assemble two parts, while moving mouse on assembled parts it always highlights two pats, showing its lines and volumes.Such like is their any option or method to show...

31 December 2014 336 1 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to upload pdf of my articles published?

How to upload pdf of my articles published?

03 March 2021 2,183 3 View

Is SSRN e-Journal Scopus indexed?

I have publication in SSRN. I want to know whether it is Scopus indexed? Does it show impact factor? What is its ISSN No.?

02 March 2021 4,565 3 View

Would adding books published in Lambert Publishers increase my RG impact?

There are some books published in LAP. Shall I add it to the RG?

02 March 2021 2,753 1 View

What is the most reliable source to get Impact factor of journals?

Source to get Impact factor of journals

01 March 2021 6,654 2 View

Is Journal of Agricultural Research a predator?

it is published by Juniper

28 February 2021 354 4 View

How can I publish a manuscript in free or low cost journal with good H-Index?

Dear all I am going to publish my manuscript which is from my thesis in a good H-Index journal but I found them very expensive(I don't have financial support) based on the exchange currency of my...

28 February 2021 7,800 6 View

Where can I find public datasets with Covid-19 patient information?

Hi, I'm looking for public datasets that have CT, X-ray information, or medical records for patients with Covid-19. Does anyone have suggestions?

28 February 2021 4,760 3 View

Which software is better to write systematic review paper?

We have seen some authors use some software to write review paper. As obvious, the study of all published papers concerning our studying field is not possible and these software can help us to...

27 February 2021 6,296 1 View

How to get rid of somebody pretending to be the author of a publication?

One of the publication I co-authored has the author's name in abbreviation. Then, somebody whose nothing to do with that paper acquired it as her work. To whom in this RG shall I ask for a hand,...

27 February 2021 4,206 4 View