How to draw Spiral (helix) stirrups (transverse reinforcement) in Ansys workbench??

More Othman AlShareedah's questions See All

Can i get some political blogs going?

I'm looking for some blogs It is also possible corpus

14 April 2024 2,090 0 View

How to get AIM for whole sample?

Dear respected Professor and experts in this platform. I would like to ask if anyone here has ever encountered the same problem of getting AIM file, specifically on how to get an AIM file of the...

03 April 2024 2,310 0 View

Is there a validated questionnaire about caregivers' health-care seeking behaviours for common childhood illnesses ?

Hello everyone, I hope everything is going well with you I'm looking for a validated questionnaire to use in a study to assess caregivers' health-care seeking behaviours for common childhood...

15 September 2023 4,561 0 View

Seeking guidance for validation of a questionnaire?

Dear Academics/expertise I am writing to seek your guidance and validation for the questionnaire that I have developed as a crucial component of my PhD thesis research in management. I kindly...

15 September 2023 8,973 2 View

How to measure current density for electro-oxidation setup with 6 anodes and 7 cathodes?

I have a electrooxidation setup that have 6 anodes and 7 cathodes in alternate arrangement. The surface area of the plate is 1m2 and the applied current is 100A. How to measure the current density...

28 August 2023 164 1 View

How can I avoid the background noise after meusring Floresense with Sytox Green?

I use the HL-60 cell line in conjunction with Sytox Green ( 5µm) to detect extracellular DNA. The cells were suspended in both PBS and complete RPMI. My concern is that the vialable cell group...

06 June 2023 5,301 3 View

In rain modeling by SDSM ????

Hello... In rain modeling by SDSM, there are empty values in the meteorological station file. Should I leave it empty or put a zero? Does it affect the modeling values? and what does the total...

01 June 2023 1,994 2 View

Esclavage moderne : L'être humain dépendant de la technologie! agree or not?

L'apparition des nouvelles technologies de l'information et de la communication (NTIC) a bouleversé le monde entier, et au cours de la dernière décennie, l'être humain a vécu une révolution...

30 May 2023 9,918 0 View

How to rotate a cylinder (geom and results) in comsol?

Hi I am doing a simulation of a cylinder between two walls (2D) using comsol. I divided my simulation into two studies. 1. study 1 (time dependent) the cylinder is at position 1. 2. After...

26 August 2022 5,263 0 View

AHP pairwise comparison?

i'm doing AHP and pairwise comparison for 5 criteria. Seems all respondents showed consistency ratio CR more than 0.1. Is that even possible? Any suggestion to resolve this?

20 August 2022 9,621 26 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View

Pankaj Biswas

You can make it in ANSYS workbench also.

Othman AlShareedah

Mr Biswas, Thanks for your answer but I didn't find any video or instruction of how to draw spiral in workbench

Thanks Mahmoud

Axis of rotation, cross-section and dimension of pitch of spiral are required for this. You have to do it in design modular.